Y901200D Roundness Measuring Instrument

Roundness Measuring Instrument

ModellY901200D

    By submitting you agree to our privacy policy.

    01

    Überblick

    Y901200D低速大承载圆度测量仪适用于直径小于1.2米、重量小于500Kg的大型环形工件、各种大型轴承内外套圈滚道的圆度、波纹度等参数的测量(可用四种方法评定圆度误差)并能够给出零件的偏心及相位。亦可用于各种电机整流子的圆度、跳动量、单片跳动、邻片间跳动等参数的测量并能够给出零件的偏心及相位。
    主要特点
    1、仪器采用自主研发的伸缩式测量机构,测量方便节省空间。仪器测量转台采用特殊工艺制作的高精度气浮静压轴承结构,回转精度高不磨损,承载大,使用寿命长;
    2、主轴电机采用进口高精度交流伺服电机,自研柔性联轴器,使仪器仪器主轴旋转精度更平稳可靠。数据采集采用德国HEIDENHAIN公司进口精密圆光栅及相关技术,定位精确,稳定性好;
    3、仪器采用WINDOWS系统操作平台,专业测量软件,测量界面简洁直观,操作便捷;可以实时显示图形数据、存盘留档、随时打印,图形分析报告,直观清晰;
    4、传感器垂直和水平运动采用电控与手动控制,使设备操作方便,调整精确;
    5、可对零件表面状态进行频谱分析,能够给出任一波的幅值;自动识别间断,自动和手动剔除凹口功能,部分圆弧测量圆度功能;
    6、测量操作设置鼠标和键盘快捷操作,用户可根据操作习惯自由选择
    型号、项目
    Y901200D
    主轴精度
    径向误差
    ±(0.05+5H/10000)μm
    轴向误差
    ±(0.05+6X/10000)μm
    系统精度
    0.19μm
    工作台平面度
    ≤2 μm(半径R≤70mm)
    数据采集方式
    进口德国HEIDENHAIN精密圆光栅
    数据采集点
    4096
    测量最大外径
    Ф1200mm(可扩展)
    测量最小内径
    Ф5mm
    测量最大高度
    400mm(可增高)
    最大承载
    500Kg
    量程范围
    ≤0.3mm(半径差)
    传感器分辨率
    0.01μm
    传感器测力
    0.2N
    滤波器
    2-15、2-50、2-150、2-500、15-150、1
    波纹度
    3-16、17-100
    圆度误差评定方法
    最小二乘法(LSC)、最小区域法(MZC)、最大外接圆(MIC)、最小包容圆法(MCC)
    放大倍率
    100、200、400、500、800、1000、2000、4000、5000、8000、10000、20000、40000、50000、80000、100000、200000等共17档。
    频谱分析
    可给出任一频段的数据值
    转速
    4-6转/分
    X/Y轴移动方式
    电动/手动
    凹凸口剔除
    自动识别间断,自动和手动剔除凹口功能,部分圆弧测量圆度功能;
    软件辅助功能
    同轴度、垂直度、平行度、平面度
    电源、气源压力
    电源220V、50V、250W;气源压力≥0.45MPa
    环境要求
    工作温度:常温;湿度:20-80%RH(无结露);良好地线,无明显震源

    Y901200D Roundness Measuring Instrument supplied by CHWES. 0 key specifications available on request.

    02

    Technische Daten

    * Generated by rule engine over the product database; for pre-selection only.

    03

    Messprinzip

    A stylus instrument drags a diamond tip (2 or 5 µm radius) across the surface under constant force. The tip follows micro-relief, an inductive transducer converts displacement into a signal, and after amplification and filtering the profile is obtained. Per GB/T 10610 a Gaussian filter (or phase-corrected 2RC) with cut-off λc separates roughness from waviness; Ra, Rz, Rq, Rt and RSm are then computed over the sampling length.

    Profile instruments share the same precision guide to capture roughness and macro profile, evaluating straightness, arc radius, angle, groove depth and pitch. Long-travel models (160–300 mm X, ±5 mm Z) suit shafts, rolls and mould surfaces.

    • λc: 0.8 mm for Ra 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm.
    • Force: 0.75 mN typical, below 0.4 mN for soft materials.
    • Direction: normally perpendicular to the machining lay.
    04

    Process animation

    1. Clean and level: wipe with lint-free cloth, align the part to the guide within 1°.
    2. Select cut-off: choose λc from the expected Ra, sampling length usually 5 × λc.
    3. Lower the stylus: automatic descent, zero after the force stabilises.
    4. Traverse: constant speed, acquire the profile.
    5. Filter and compute: Gaussian filter separates roughness, output Ra/Rz/Rq.
    6. Average: three positions per surface.
    0102030405
    05

    Calculation & formulas

    1. Ra: arithmetic mean deviation, Ra = (1/n)Σ|zi| for sampled points; samples of 2, 4, 3, 5, 1 µm give Ra = 3 µm.

    2. Rz: mean of the five highest peaks and five deepest valleys per sampling length (maximum peak-to-valley under GB/T 3505).

    3. Rmr: material ratio curve at height c, describing the bearing capability of mating faces.

    4. Filtering: Gaussian λc = 0.8/2.5/8 mm separates roughness from waviness; λs suppresses noise.

    5. Roundness: least-squares centre, minimum-zone, minimum circumscribed or maximum inscribed; spindle error should be under 1/5 of the tolerance.

    06

    Normen

    StandardTitleUse
    GB/T 1031-2009Surface roughness — parameters and valuesParameter limits
    GB/T 3505-2009Surface texture — profile termsTerminology
    GB/T 10610-2009Rules and procedures for assessmentFiltering, evaluation
    ISO 4287Profile method — termsExport projects
    ISO 4288Rules and proceduresSampling length
    07

    Auswahl

    1. Separate three quantities: roughness (Ra/Rz/Rmr, micrometre-scale microtexture), waviness (W, 0.1–10 µm mid-spatial), and form error (roundness, cylindricity, macro geometry). They need different instruments or filters.

    2. Profilometers and roundness testers are not interchangeable: profilometers measure Ra/Rz and profile along a line (XZ, CX series); roundness testers measure roundness, cylindricity and coaxiality of bodies of revolution (Y90 series). A cylinder bore needing both requires two machines or a combined type.

    3. Sensor range sets capability: ±50 µm suffices for Ra alone; deep grooves, steps and large arcs need ±500 µm or more; mirror surfaces below Ra 0.01 µm need low-noise sensors and isolation.

    4. Travel and load: XZ-150 for small parts, XZ-230/XZ-150G for mid-size bores and shafts, Y901200 or custom stages above one metre.

    5. Software must support the standards: full Ra/Rz/Rq/Rsk/Rku/Rmr per GB/T 1031 and ISO 4287; roundness per GB/T 7234 with minimum-zone, least-squares, minimum-circumscribed and maximum-inscribed evaluation.

    6. On-site use: workshops need vibration and dust control; portable units (DY-300) suit large parts at lower accuracy.

    ModelTypeCapabilityTypical parts
    XZ-150 / XZ-150GRoughness and profileRa/Rz + profileSmall precision parts
    XZ-230Roughness and profileRa/Rz + long travelShafts, cylinder bores
    CX-1(S) / CX-1(G)RoughnessRa/Rz/RmrShop-floor sampling
    CX-3/100 / CX-3/160Roughness and profileRa + profile + stepsSpools, sealing faces
    2207 / 2302ARoundnessRoundness/cylindricityBearing rings, journals
    Y9025B/C/DRoundnessRoundness/coaxiality/wavinessPrecision spindles, bores
    Y9060 / Y901200Large roundnessLarge-diameter roundnessWind bearings, flanges
    DY-300PortableRa/RzLarge parts on site

    Why results disagree: wrong cut-off wavelength, insufficient evaluation length, mismatched stylus radius and an unlevelled part account for most disputes.

    08

    Prüfverfahren

    Preparation. Clean with ethanol to remove oil and chips; let the part stabilise to ambient (±2 °C); inspect the stylus at 20× for wear.

    Settings. Choose λc to GB/T 1031 from expected Ra: 0.25 mm up to 0.1 µm, 0.8 mm for 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm; evaluation length 5 × λc.

    Measurement. Stylus perpendicular to the lay, lower slowly, start when force is stable. Measure at least three positions per surface and average; on cylinders follow the generatrix.

    Judgement. Compare with the drawing limit; no single reading should exceed 1.2 × the limit. Arbitrate with a profile instrument and a certified specimen.

    Quality control. Daily check against Ra 0.4/1.6/6.3 specimens, recalibrate beyond 5% deviation, replace or verify the stylus every 12 months.

    09

    Industry applications

    • Hydraulics and pneumatics: Ra/Rz and Rmr on spools, cylinder bores and valve blocks, governing leakage and oil-film load capacity.
    • Bearings and spindles: raceway roundness, cylindricity and waviness, the latter being the main source of vibration and noise.
    • Engines and transmissions: bore roundness and cylindricity, crank-journal roundness, big-end bore form error.
    • Sealing faces: O-ring groove roughness and flange waviness affecting seal reliability.
    • Optics and semiconductors: Ra ≤0.005 µm, flatness and waviness requiring high-resolution sensors and isolation.
    • Moulds: cavity polish Ra and draft-face texture direction, affecting release and appearance.
    • Additive manufacturing: as-built Ra and support residue for post-processing validation.
    • Tools and coatings: edge honing radius and its correlation with coating roughness and adhesion.
    10

    Price and lead time for this model

    By submitting you agree to our privacy policy.

    ⇄0VergleichTechnischer Vergleich