Y9025DG Roundness Measuring Instrument

Roundness Measuring Instrument

ModellY9025DG
  • 主轴精度径向误差 / ±(0.0125+3H/10000)μm
  • 轴向误差±(0.0125+4X/10000)μm
  • 系统精度0.03μm
  • 工作台平面度≤2μm(R≤70mm)

By submitting you agree to our privacy policy.

01

Überblick

Y9025DG低速大承载圆度测量仪适用于各种非连续表面,规则、不规则的环形工件的圆度、波纹度、同轴度、垂直度、平行度、平面度等参数的测量(可用四种方法评定圆度误差)并能够给出零件的偏心及相位。亦可用于各种电机整流子的圆度、跳动量、单片跳动、邻片间跳动等参数的测量(可用四种方法评定)并能够给出零件的偏心及相位。
主要特点
1、仪器回转测量转台采用高精度气浮静压轴承结构,仪器主轴精度高不磨损,使用寿命长;
2、数据采集采用德国HEIDENHAIN公司进口精密圆光栅及相关技术,定位精确,稳定性好;
3、仪器采用WINDOWS系统操作平台,专业测量软件,测量界面简洁直观,操作便捷;可以实时显示图形数据、存盘留档、随时打印,图形分析报告,直观清晰;
4、仪器标配万向调平工作台,工件调整方便快捷,检测效率高;
5、仪器配置各种规格、长度的红宝石测针,可选配本公司特制尼龙测头测量特殊工件;
6、电机整流子测量采用专用测量及处理软件,同一界面可显示圆度、跳动量、单片跳动、邻片间跳动等参数值;
7、对使用环境无特殊要求,可在车间及计量室使用;
8、可对零件表面状态进行频谱分析,能够给出任一波的幅值;
9、自动识别间断,自动和手动剔除凹口功能,部分圆弧测量圆度功能;
10、测量操作设置鼠标和键盘快捷操作,用户可根据操作习惯自由选择。
主要参数
型号、项目
Y9025DG
主轴精度
径向误差
±(0.0125+3H/10000)μm
轴向误差
±(0.0125+4X/10000)μm
系统精度
0.03μm
工作台平面度
≤2μm(R≤70mm)
数据采集方式
进口德国HEIDENHAIN精密圆光栅
数据采集点
4096
测量最大外径
Ф200mm(可扩展)
测量最小内径
Ф3mm
测量最大高度
300mm可增高600mm
最大承载
15Kg
量程范围
≤400μm(半径差)
传感器分辨率
0.01μm
传感器测力
0.2N
滤波器
1、1-500、2-500、2-15、2-50、2-150、15-150
波纹度
3-16、17-100
圆度误差
评定方法
最小二乘法(LSC)、最小区域法(MZC)
最大外接圆(MIC)、 最小包容圆法(MCC)
放大倍率
100、200、400、500、800、1000、2000、4000、5000
8000、10000、20000、40000、50000、80000、100000
200000等共17档。
频谱分析
可给出任一频段的数据值
转速
4-6转/分
X/Y轴移动方式
电动/手动
凹凸口剔除
自动识别间断,自动和手动剔除凹口功能,部分圆弧测量圆度功能;
软件辅助功能
同轴度、垂直度、平行度、平面度
电源、气源压力
电源220V、50V、250W;气源压力≥0.45MPa
环境要求
工作温度:常温;湿度:20-80%RH(无结露);良好地线,无明显震源

Y9025DG Roundness Measuring Instrument supplied by CHWES. 24 key specifications available on request.

02

Technische Daten

主轴精度径向误差 / ±(0.0125+3H/10000)μm
轴向误差±(0.0125+4X/10000)μm
系统精度0.03μm
工作台平面度≤2μm(R≤70mm)
数据采集方式进口德国HEIDENHAIN精密圆光栅
数据采集点4096
测量最大外径Ф200mm(可扩展)
测量最小内径Ф3mm
测量最大高度300mm可增高600mm
最大承载15Kg
量程范围≤400μm(半径差)
传感器分辨率0.01μm
传感器测力0.2N
滤波器1、1-500、2-500、2-15、2-50、2-150、15-150
波纹度3-16、17-100
圆度误差 评定方法最小二乘法(LSC)、最小区域法(MZC) 最大外接圆(MIC)、 最小包容圆法(MCC)
放大倍率100、200、400、500、800、1000、2000、4000、5000 8000、10000、20000、40000、50000、80000、100000 200000等共17档。
频谱分析可给出任一频段的数据值
转速4-6转/分
X/Y轴移动方式电动/手动
凹凸口剔除自动识别间断,自动和手动剔除凹口功能,部分圆弧测量圆度功能;
软件辅助功能同轴度、垂直度、平行度、平面度
电源、气源压力电源220V、50V、250W;气源压力≥0.45MPa
环境要求工作温度:常温;湿度:20-80%RH(无结露);良好地线,无明显震源

* Generated by rule engine over the product database; for pre-selection only.

03

Messprinzip

A stylus instrument drags a diamond tip (2 or 5 µm radius) across the surface under constant force. The tip follows micro-relief, an inductive transducer converts displacement into a signal, and after amplification and filtering the profile is obtained. Per GB/T 10610 a Gaussian filter (or phase-corrected 2RC) with cut-off λc separates roughness from waviness; Ra, Rz, Rq, Rt and RSm are then computed over the sampling length.

Profile instruments share the same precision guide to capture roughness and macro profile, evaluating straightness, arc radius, angle, groove depth and pitch. Long-travel models (160–300 mm X, ±5 mm Z) suit shafts, rolls and mould surfaces.

  • λc: 0.8 mm for Ra 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm.
  • Force: 0.75 mN typical, below 0.4 mN for soft materials.
  • Direction: normally perpendicular to the machining lay.
04

Process animation

  1. Clean and level: wipe with lint-free cloth, align the part to the guide within 1°.
  2. Select cut-off: choose λc from the expected Ra, sampling length usually 5 × λc.
  3. Lower the stylus: automatic descent, zero after the force stabilises.
  4. Traverse: constant speed, acquire the profile.
  5. Filter and compute: Gaussian filter separates roughness, output Ra/Rz/Rq.
  6. Average: three positions per surface.
0102030405
05

Calculation & formulas

1. Ra: arithmetic mean deviation, Ra = (1/n)Σ|zi| for sampled points; samples of 2, 4, 3, 5, 1 µm give Ra = 3 µm.

2. Rz: mean of the five highest peaks and five deepest valleys per sampling length (maximum peak-to-valley under GB/T 3505).

3. Rmr: material ratio curve at height c, describing the bearing capability of mating faces.

4. Filtering: Gaussian λc = 0.8/2.5/8 mm separates roughness from waviness; λs suppresses noise.

5. Roundness: least-squares centre, minimum-zone, minimum circumscribed or maximum inscribed; spindle error should be under 1/5 of the tolerance.

06

Normen

StandardTitleUse
GB/T 1031-2009Surface roughness — parameters and valuesParameter limits
GB/T 3505-2009Surface texture — profile termsTerminology
GB/T 10610-2009Rules and procedures for assessmentFiltering, evaluation
ISO 4287Profile method — termsExport projects
ISO 4288Rules and proceduresSampling length
07

Auswahl

1. Separate three quantities: roughness (Ra/Rz/Rmr, micrometre-scale microtexture), waviness (W, 0.1–10 µm mid-spatial), and form error (roundness, cylindricity, macro geometry). They need different instruments or filters.

2. Profilometers and roundness testers are not interchangeable: profilometers measure Ra/Rz and profile along a line (XZ, CX series); roundness testers measure roundness, cylindricity and coaxiality of bodies of revolution (Y90 series). A cylinder bore needing both requires two machines or a combined type.

3. Sensor range sets capability: ±50 µm suffices for Ra alone; deep grooves, steps and large arcs need ±500 µm or more; mirror surfaces below Ra 0.01 µm need low-noise sensors and isolation.

4. Travel and load: XZ-150 for small parts, XZ-230/XZ-150G for mid-size bores and shafts, Y901200 or custom stages above one metre.

5. Software must support the standards: full Ra/Rz/Rq/Rsk/Rku/Rmr per GB/T 1031 and ISO 4287; roundness per GB/T 7234 with minimum-zone, least-squares, minimum-circumscribed and maximum-inscribed evaluation.

6. On-site use: workshops need vibration and dust control; portable units (DY-300) suit large parts at lower accuracy.

ModelTypeCapabilityTypical parts
XZ-150 / XZ-150GRoughness and profileRa/Rz + profileSmall precision parts
XZ-230Roughness and profileRa/Rz + long travelShafts, cylinder bores
CX-1(S) / CX-1(G)RoughnessRa/Rz/RmrShop-floor sampling
CX-3/100 / CX-3/160Roughness and profileRa + profile + stepsSpools, sealing faces
2207 / 2302ARoundnessRoundness/cylindricityBearing rings, journals
Y9025B/C/DRoundnessRoundness/coaxiality/wavinessPrecision spindles, bores
Y9060 / Y901200Large roundnessLarge-diameter roundnessWind bearings, flanges
DY-300PortableRa/RzLarge parts on site

Why results disagree: wrong cut-off wavelength, insufficient evaluation length, mismatched stylus radius and an unlevelled part account for most disputes.

08

Prüfverfahren

Preparation. Clean with ethanol to remove oil and chips; let the part stabilise to ambient (±2 °C); inspect the stylus at 20× for wear.

Settings. Choose λc to GB/T 1031 from expected Ra: 0.25 mm up to 0.1 µm, 0.8 mm for 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm; evaluation length 5 × λc.

Measurement. Stylus perpendicular to the lay, lower slowly, start when force is stable. Measure at least three positions per surface and average; on cylinders follow the generatrix.

Judgement. Compare with the drawing limit; no single reading should exceed 1.2 × the limit. Arbitrate with a profile instrument and a certified specimen.

Quality control. Daily check against Ra 0.4/1.6/6.3 specimens, recalibrate beyond 5% deviation, replace or verify the stylus every 12 months.

09

Industry applications

  • Hydraulics and pneumatics: Ra/Rz and Rmr on spools, cylinder bores and valve blocks, governing leakage and oil-film load capacity.
  • Bearings and spindles: raceway roundness, cylindricity and waviness, the latter being the main source of vibration and noise.
  • Engines and transmissions: bore roundness and cylindricity, crank-journal roundness, big-end bore form error.
  • Sealing faces: O-ring groove roughness and flange waviness affecting seal reliability.
  • Optics and semiconductors: Ra ≤0.005 µm, flatness and waviness requiring high-resolution sensors and isolation.
  • Moulds: cavity polish Ra and draft-face texture direction, affecting release and appearance.
  • Additive manufacturing: as-built Ra and support residue for post-processing validation.
  • Tools and coatings: edge honing radius and its correlation with coating roughness and adhesion.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0VergleichTechnischer Vergleich