HOTY9025DG Roundness Measuring Instrument
Roundness Measuring Instrument
- 主轴精度径向误差 / ±(0.0125+3H/10000)μm
- 轴向误差±(0.0125+4X/10000)μm
Y9025D · 2026-11-17 · +86 21 5748 2007
Roundness Measuring Instrument
By submitting you agree to our privacy policy.
Y9025D低速圆度测量仪适用于各种非连续表面,规则、不规则的环形工件的圆度、波纹度、同轴度、垂直度、平行度、平面度等参数的测量(可用四种方法评定圆度误差)并能够给出零件的偏心及相位。亦可用于各种电机整流子的圆度、跳动量、单片跳动、邻片间跳动等参数的测量(可用四种方法评定)并能够给出零件的偏心及相位。
主要特点:
1、仪器回转测量转台采用高精度气浮静压轴承结构,仪器主轴精度高不磨损,使用寿命长;
2、数据采集采用德国HEIDENHAIN公司进口精密圆光栅及相关技术,定位精确,稳定性好;
3、仪器采用WINDOWS系统操作平台,专业测量软件,测量界面简洁直观,操作便捷;可以实时显示图形数据、存盘留档、随时打印,图形分析报告,直观清晰;
4、仪器标配万向调平工作台,工件调整方便快捷,检测效率高;
5、仪器配置各种规格、长度的红宝石测针,可选配本公司特制尼龙测头测量特殊工件;
6、电机整流子测量采用专用测量及处理软件,同一界面可显示圆度、跳动量、单片跳动、邻片间跳动等参数值;
7、对使用环境无特殊要求,可在车间及计量室使用;
8、可对零件表面状态进行频谱分析,能够给出任一波的幅值;
9、自动识别间断,自动和手动剔除凹口功能,部分圆弧测量圆度功能;
10、测量操作设置鼠标和键盘快捷操作,用户可根据操作习惯自由选择。
主要参数
型号、项目
Y9025D
主轴精度
径向误差
±(0.025+5H/10000)μm
轴向误差
±(0.025+6X/10000)μm
系统精度
0.06μm
工作台平面度
≤2μm(R≤70mm)
数据采集方式
进口德国HEIDENHAIN精密圆光栅
数据采集点
4096
测量最大外径
Ф200mm(可扩展)
测量最小内径
Ф3mm
测量最大高度
300mm可增高600mm
最大承载
15Kg
量程范围
≤400μm(半径差)
传感器分辨率
0.01μm
传感器测力
0.2N
滤波器
1、1-500、2-500、2-15、2-50、2-150、15-150
波纹度
3-16、17-100
圆度误差
评定方法
最小二乘法(LSC)、最小区域法(MZC)
最大外接圆(MIC)、 最小包容圆法(MCC)
放大倍率
100、 200、 400、 500、 800、 1000、 2000、 4000、5000
8000、 10000、 20000、 40000、50000、 80000、 100000
200000 等共17档。
频谱分析
可给出任一频段的数据值
转速
4-6转/分
X/Y轴移动方式
电动/手动
凹凸口剔除
自动识别间断,自动和手动剔除凹口功能,部分圆弧测量圆度功能;
软件辅助功能
同轴度、垂直度、平行度、平面度
电源、气源压力
电源:220V、50V、250W;气源压力≥0.45MPa
环境要求
工作温度:常温;湿度:20-80%RH(无结露);良好地线,无明显震源
Y9025D Roundness Measuring Instrument supplied by CHWES. 24 key specifications available on request.
| 主轴精度 | 径向误差 / ±(0.025+5H/10000)μm |
|---|---|
| 轴向误差 | ±(0.025+6X/10000)μm |
| 系统精度 | 0.06μm |
| 工作台平面度 | ≤2μm(R≤70mm) |
| 数据采集方式 | 进口德国HEIDENHAIN精密圆光栅 |
| 数据采集点 | 4096 |
| 测量最大外径 | Ф200mm(可扩展) |
| 测量最小内径 | Ф3mm |
| 测量最大高度 | 300mm可增高600mm |
| 最大承载 | 15Kg |
| 量程范围 | ≤400μm(半径差) |
| 传感器分辨率 | 0.01μm |
| 传感器测力 | 0.2N |
| 滤波器 | 1、1-500、2-500、2-15、2-50、2-150、15-150 |
| 波纹度 | 3-16、17-100 |
| 圆度误差 评定方法 | 最小二乘法(LSC)、最小区域法(MZC) 最大外接圆(MIC)、 最小包容圆法(MCC) |
| 放大倍率 | 100、 200、 400、 500、 800、 1000、 2000、 4000、5000 8000、 10000、 20000、 40000、50000、 80000、 100000 200000 等共17档。 |
| 频谱分析 | 可给出任一频段的数据值 |
| 转速 | 4-6转/分 |
| X/Y轴移动方式 | 电动/手动 |
| 凹凸口剔除 | 自动识别间断,自动和手动剔除凹口功能,部分圆弧测量圆度功能; |
| 软件辅助功能 | 同轴度、垂直度、平行度、平面度 |
| 电源、气源压力 | 电源:220V、50V、250W;气源压力≥0.45MPa |
| 环境要求 | 工作温度:常温;湿度:20-80%RH(无结露);良好地线,无明显震源 |
* Generated by rule engine over the product database; for pre-selection only.
A stylus instrument drags a diamond tip (2 or 5 µm radius) across the surface under constant force. The tip follows micro-relief, an inductive transducer converts displacement into a signal, and after amplification and filtering the profile is obtained. Per GB/T 10610 a Gaussian filter (or phase-corrected 2RC) with cut-off λc separates roughness from waviness; Ra, Rz, Rq, Rt and RSm are then computed over the sampling length.
Profile instruments share the same precision guide to capture roughness and macro profile, evaluating straightness, arc radius, angle, groove depth and pitch. Long-travel models (160–300 mm X, ±5 mm Z) suit shafts, rolls and mould surfaces.
1. Ra: arithmetic mean deviation, Ra = (1/n)Σ|zi| for sampled points; samples of 2, 4, 3, 5, 1 µm give Ra = 3 µm.
2. Rz: mean of the five highest peaks and five deepest valleys per sampling length (maximum peak-to-valley under GB/T 3505).
3. Rmr: material ratio curve at height c, describing the bearing capability of mating faces.
4. Filtering: Gaussian λc = 0.8/2.5/8 mm separates roughness from waviness; λs suppresses noise.
5. Roundness: least-squares centre, minimum-zone, minimum circumscribed or maximum inscribed; spindle error should be under 1/5 of the tolerance.
| Standard | Title | Use |
|---|---|---|
| GB/T 1031-2009 | Surface roughness — parameters and values | Parameter limits |
| GB/T 3505-2009 | Surface texture — profile terms | Terminology |
| GB/T 10610-2009 | Rules and procedures for assessment | Filtering, evaluation |
| ISO 4287 | Profile method — terms | Export projects |
| ISO 4288 | Rules and procedures | Sampling length |
1. Separate three quantities: roughness (Ra/Rz/Rmr, micrometre-scale microtexture), waviness (W, 0.1–10 µm mid-spatial), and form error (roundness, cylindricity, macro geometry). They need different instruments or filters.
2. Profilometers and roundness testers are not interchangeable: profilometers measure Ra/Rz and profile along a line (XZ, CX series); roundness testers measure roundness, cylindricity and coaxiality of bodies of revolution (Y90 series). A cylinder bore needing both requires two machines or a combined type.
3. Sensor range sets capability: ±50 µm suffices for Ra alone; deep grooves, steps and large arcs need ±500 µm or more; mirror surfaces below Ra 0.01 µm need low-noise sensors and isolation.
4. Travel and load: XZ-150 for small parts, XZ-230/XZ-150G for mid-size bores and shafts, Y901200 or custom stages above one metre.
5. Software must support the standards: full Ra/Rz/Rq/Rsk/Rku/Rmr per GB/T 1031 and ISO 4287; roundness per GB/T 7234 with minimum-zone, least-squares, minimum-circumscribed and maximum-inscribed evaluation.
6. On-site use: workshops need vibration and dust control; portable units (DY-300) suit large parts at lower accuracy.
| Model | Type | Capability | Typical parts |
|---|---|---|---|
| XZ-150 / XZ-150G | Roughness and profile | Ra/Rz + profile | Small precision parts |
| XZ-230 | Roughness and profile | Ra/Rz + long travel | Shafts, cylinder bores |
| CX-1(S) / CX-1(G) | Roughness | Ra/Rz/Rmr | Shop-floor sampling |
| CX-3/100 / CX-3/160 | Roughness and profile | Ra + profile + steps | Spools, sealing faces |
| 2207 / 2302A | Roundness | Roundness/cylindricity | Bearing rings, journals |
| Y9025B/C/D | Roundness | Roundness/coaxiality/waviness | Precision spindles, bores |
| Y9060 / Y901200 | Large roundness | Large-diameter roundness | Wind bearings, flanges |
| DY-300 | Portable | Ra/Rz | Large parts on site |
Why results disagree: wrong cut-off wavelength, insufficient evaluation length, mismatched stylus radius and an unlevelled part account for most disputes.
Preparation. Clean with ethanol to remove oil and chips; let the part stabilise to ambient (±2 °C); inspect the stylus at 20× for wear.
Settings. Choose λc to GB/T 1031 from expected Ra: 0.25 mm up to 0.1 µm, 0.8 mm for 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm; evaluation length 5 × λc.
Measurement. Stylus perpendicular to the lay, lower slowly, start when force is stable. Measure at least three positions per surface and average; on cylinders follow the generatrix.
Judgement. Compare with the drawing limit; no single reading should exceed 1.2 × the limit. Arbitrate with a profile instrument and a certified specimen.
Quality control. Daily check against Ra 0.4/1.6/6.3 specimens, recalibrate beyond 5% deviation, replace or verify the stylus every 12 months.