XZ-400 Surface Contour Measuring Instrument

Surface Contour Measuring Instrument

ModellXZ-400
  • 测量 范围Z轴方向测量高度 / ≤Φ600mm / ≤1200mm
  • X轴移动最大距离400mm
  • 最小测量孔径Φ9mm
  • 可移动气浮测量装置X轴导轨移动直线度 / 0.5μm/100mm

By submitting you agree to our privacy policy.

01

Überblick

XZ-400型形状测量仪概况
根据某些工件的特殊性,为不同客户提供大型工件的检测需求。我公司研制生产出国内较早大型异形工件XZT-400型系列检测设备。该设备改变了传统运动测量方式,采用天然大理石与气浮式精密导轨作为移动测量,特制靠板装置将被测工件静态不动,随意摆放。进口开式光栅尺保障移动精度更准确,测量范围更大。该设备X轴方向移动可用手动,电动控制,装调方便,操作简单,测量效率高,能满足各个规格产品的测量,是大型工件检测的正确解决方案。
该仪器可测量各种机械零件的素线和截面轮廓形状参数,在轴承行业中可测量各种零件的直线度、平行度、倾斜度、角度处理、圆处理(直线到切线的距离、圆心到圆心距离、圆弧半径、交点到圆的心距离、圆心到直线距离)、点线处理(交点到直线距离、交点到圆心距离、两直线交点、交点与交点距离)、对数曲线、槽宽、槽深、沟边距、沟心距、倾斜度、水平距离、垂直距离等形状参数。
仪器采用计算机控制,直接显示所测零件的轮廓形状,并可在显示的轮廓形状线上直接标注参数,也可以打印图形和数据,供产品质量检测及工艺分析。
2、仪器技术参数:
名称
XZ-400A
XZ-400B
测量
范围
Z轴方向测量高度
≤Φ600mm
≤1200mm
X轴移动最大距离
400mm
最小测量孔径
Φ9mm
可移动气浮测量装置
X轴导轨移动直线度
0.5μm/100mm
导轨移动距离精度
(进口光栅尺)
分辨率:1μm
精度:3μm/全行程
承重
400kg
传感器
测针上下移动(量程)
6mm(可扩展12 mm)
垂直分辨率
1/65536
调整装置可调范围
X轴水平方向可调45°;Y轴前后方向可调10 mm;扇形方向可调10°
其他
测量精度(半径误差)
0.1~1%
重复测量精度
3%
测量速度
0.1~0.4 mm/s分3档选择
电源
0.5 kW/220V/50Hz
气源压力
≥0.5MPa

XZ-400 Surface Contour Measuring Instrument supplied by CHWES. 14 key specifications available on request.

02

Technische Daten

测量 范围Z轴方向测量高度 / ≤Φ600mm / ≤1200mm
X轴移动最大距离400mm
最小测量孔径Φ9mm
可移动气浮测量装置X轴导轨移动直线度 / 0.5μm/100mm
导轨移动距离精度 (进口光栅尺)分辨率:1μm 精度:3μm/全行程
承重400kg
传感器测针上下移动(量程) / 6mm(可扩展12 mm)
垂直分辨率1/65536
调整装置可调范围X轴水平方向可调45°;Y轴前后方向可调10 mm;扇形方向可调10°
其他测量精度(半径误差) / 0.1~1%
重复测量精度3%
测量速度0.1~0.4 mm/s分3档选择
电源0.5 kW/220V/50Hz
气源压力≥0.5MPa

* Generated by rule engine over the product database; for pre-selection only.

03

Messprinzip

A stylus instrument drags a diamond tip (2 or 5 µm radius) across the surface under constant force. The tip follows micro-relief, an inductive transducer converts displacement into a signal, and after amplification and filtering the profile is obtained. Per GB/T 10610 a Gaussian filter (or phase-corrected 2RC) with cut-off λc separates roughness from waviness; Ra, Rz, Rq, Rt and RSm are then computed over the sampling length.

Profile instruments share the same precision guide to capture roughness and macro profile, evaluating straightness, arc radius, angle, groove depth and pitch. Long-travel models (160–300 mm X, ±5 mm Z) suit shafts, rolls and mould surfaces.

  • λc: 0.8 mm for Ra 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm.
  • Force: 0.75 mN typical, below 0.4 mN for soft materials.
  • Direction: normally perpendicular to the machining lay.
04

Process animation

  1. Clean and level: wipe with lint-free cloth, align the part to the guide within 1°.
  2. Select cut-off: choose λc from the expected Ra, sampling length usually 5 × λc.
  3. Lower the stylus: automatic descent, zero after the force stabilises.
  4. Traverse: constant speed, acquire the profile.
  5. Filter and compute: Gaussian filter separates roughness, output Ra/Rz/Rq.
  6. Average: three positions per surface.
0102030405
05

Calculation & formulas

1. Ra: arithmetic mean deviation, Ra = (1/n)Σ|zi| for sampled points; samples of 2, 4, 3, 5, 1 µm give Ra = 3 µm.

2. Rz: mean of the five highest peaks and five deepest valleys per sampling length (maximum peak-to-valley under GB/T 3505).

3. Rmr: material ratio curve at height c, describing the bearing capability of mating faces.

4. Filtering: Gaussian λc = 0.8/2.5/8 mm separates roughness from waviness; λs suppresses noise.

5. Roundness: least-squares centre, minimum-zone, minimum circumscribed or maximum inscribed; spindle error should be under 1/5 of the tolerance.

06

Normen

StandardTitleUse
GB/T 1031-2009Surface roughness — parameters and valuesParameter limits
GB/T 3505-2009Surface texture — profile termsTerminology
GB/T 10610-2009Rules and procedures for assessmentFiltering, evaluation
ISO 4287Profile method — termsExport projects
ISO 4288Rules and proceduresSampling length
07

Auswahl

1. Separate three quantities: roughness (Ra/Rz/Rmr, micrometre-scale microtexture), waviness (W, 0.1–10 µm mid-spatial), and form error (roundness, cylindricity, macro geometry). They need different instruments or filters.

2. Profilometers and roundness testers are not interchangeable: profilometers measure Ra/Rz and profile along a line (XZ, CX series); roundness testers measure roundness, cylindricity and coaxiality of bodies of revolution (Y90 series). A cylinder bore needing both requires two machines or a combined type.

3. Sensor range sets capability: ±50 µm suffices for Ra alone; deep grooves, steps and large arcs need ±500 µm or more; mirror surfaces below Ra 0.01 µm need low-noise sensors and isolation.

4. Travel and load: XZ-150 for small parts, XZ-230/XZ-150G for mid-size bores and shafts, Y901200 or custom stages above one metre.

5. Software must support the standards: full Ra/Rz/Rq/Rsk/Rku/Rmr per GB/T 1031 and ISO 4287; roundness per GB/T 7234 with minimum-zone, least-squares, minimum-circumscribed and maximum-inscribed evaluation.

6. On-site use: workshops need vibration and dust control; portable units (DY-300) suit large parts at lower accuracy.

ModelTypeCapabilityTypical parts
XZ-150 / XZ-150GRoughness and profileRa/Rz + profileSmall precision parts
XZ-230Roughness and profileRa/Rz + long travelShafts, cylinder bores
CX-1(S) / CX-1(G)RoughnessRa/Rz/RmrShop-floor sampling
CX-3/100 / CX-3/160Roughness and profileRa + profile + stepsSpools, sealing faces
2207 / 2302ARoundnessRoundness/cylindricityBearing rings, journals
Y9025B/C/DRoundnessRoundness/coaxiality/wavinessPrecision spindles, bores
Y9060 / Y901200Large roundnessLarge-diameter roundnessWind bearings, flanges
DY-300PortableRa/RzLarge parts on site

Why results disagree: wrong cut-off wavelength, insufficient evaluation length, mismatched stylus radius and an unlevelled part account for most disputes.

08

Prüfverfahren

Preparation. Clean with ethanol to remove oil and chips; let the part stabilise to ambient (±2 °C); inspect the stylus at 20× for wear.

Settings. Choose λc to GB/T 1031 from expected Ra: 0.25 mm up to 0.1 µm, 0.8 mm for 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm; evaluation length 5 × λc.

Measurement. Stylus perpendicular to the lay, lower slowly, start when force is stable. Measure at least three positions per surface and average; on cylinders follow the generatrix.

Judgement. Compare with the drawing limit; no single reading should exceed 1.2 × the limit. Arbitrate with a profile instrument and a certified specimen.

Quality control. Daily check against Ra 0.4/1.6/6.3 specimens, recalibrate beyond 5% deviation, replace or verify the stylus every 12 months.

09

Industry applications

  • Hydraulics and pneumatics: Ra/Rz and Rmr on spools, cylinder bores and valve blocks, governing leakage and oil-film load capacity.
  • Bearings and spindles: raceway roundness, cylindricity and waviness, the latter being the main source of vibration and noise.
  • Engines and transmissions: bore roundness and cylindricity, crank-journal roundness, big-end bore form error.
  • Sealing faces: O-ring groove roughness and flange waviness affecting seal reliability.
  • Optics and semiconductors: Ra ≤0.005 µm, flatness and waviness requiring high-resolution sensors and isolation.
  • Moulds: cavity polish Ra and draft-face texture direction, affecting release and appearance.
  • Additive manufacturing: as-built Ra and support residue for post-processing validation.
  • Tools and coatings: edge honing radius and its correlation with coating roughness and adhesion.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0VergleichTechnischer Vergleich