TKM-459 Hardness Tester

Hardness Tester

ModellTKM-459
  • 负载50 N(标准探头)
  • 测量范围HV240 - 9;HRC20;HB100 - 450
  • 测量精度HV:3%、HRC:1.5%、HB:4%
  • 测量显示背光液晶显示

By submitting you agree to our privacy policy.

01

Überblick

一、TKM-459超声硬度计产品介绍:
TKM-459是一种便携式超声硬度计,该款硬度计体积小巧,做工精致,此款超声硬度计受产品厚度和质量的影响非常小,解决了测量薄壁和复杂外形的产品的难题。具备现场快速测量、多种探头可供选择的特点,操作简单、直接显示测试结果。
二、TKM-459超声硬度计应用场合:
1、可测量的工件部位包括法兰盘边缘和齿轮根部
2、冲压件,工模、薄板;
3、表面硬化的齿和齿轮的测量
4、锥度部有硬度测量;
5、轴和薄壁管道、容器的测量
6、车轮、涡轮转子的硬度测量;
7、钻头的刀口的硬度测量;
8、焊接部位
三、TKM-459超声硬度计性能特点:
1、测量快速准确。
2、可以测量到不足5mm的狭槽和内孔。
3、S型、K型、H型、C型、U型多种传感器自由选择。
4、测试支架方便小尺寸零件测量
5、可自行校准仪器(通过两个标准样块可对仪器测值校准)。
6、拥有6000个数据的超大存储空间。
7、液晶显示
8、通讯接口可以与电脑进行连接
9、不受测量物内侧情况影响,适用于复杂外形和难以接触的部位。
10、测量方向可以全方向自由变化——上下左右不论哪个方向都可以不用补偿直接测量
11、.HV、HRC、HB、HSD、HRA、HRB、多种硬度制——可互相转换;
四、TKM-459超声硬度计技术参数:
1、负载:50 N(标准探头)
2、测量范围:HV240 - 940、 HRC20 - 70 、HB100 - 450
3、测量精度:HV:3%、HRC:1.5%、HB:4%
4、测量显示:背光液晶显示
5、存储:可存储6000个测量值
6、校正值存储:35
7、测量方向:全方向自由测量
8、数字显示测量值:最大值、最小值、平均值、标准偏差和测量次数
9、硬度制:布氏、洛式、维氏相互转换
10、可选择探头:5种可选择探头
11、主要测量材料:主要用来测量钢材,使用标准测试块校准后可用于高合金、特殊铸铁、非铁金属的测量
12、工作环境:-10℃-40℃
13、数据接口:通讯线缆可连接电脑
14、电源:220V-240V
15、电池:充电电池
16、尺寸:150 x 80 x 30 mm
17、重量:主机 0.4 kg
五、TKM-459超声硬度计标准配置:
主机、标准传感器、充电器、说明书、校准证明、数据线、仪器箱、仪器包
六、TKM-459超声硬度计可选附件:
1、S型传感器(50N):通用件测量
2、K型传感器:管内或狭小部位的测量
3、H型传感器 (10N):适用于镀层硬度测量
4、C型传感器(100N):未处理过的表面测量
5、U型特殊探头:便于探头定位复杂表面
6、支架:方便小尺寸零件的测量
7、各种材料的特殊硬度测量块
8、蓄电池研磨机(用于产品表面测量点的处理)

TKM-459 Hardness Tester supplied by CHWES. 17 key specifications available on request.

02

Technische Daten

负载50 N(标准探头)
测量范围HV240 - 9;HRC20;HB100 - 450
测量精度HV:3%、HRC:1.5%、HB:4%
测量显示背光液晶显示
存储可存储6000个测量值
校正值存储35
测量方向全方向自由测量
数字显示测量值最大值、最小值、平均值、标准偏差和测量次数
硬度制布氏、洛式、维氏相互转换
可选择探头5种可选择探头
主要测量材料主要用来测量钢材,使用标准测试块校准后可用于高合金、特殊铸铁、非铁金属的测量
工作环境-10℃-40℃
数据接口通讯线缆可连接电脑
电源220V-240V
电池充电电池
尺寸150 x 80 x 30 mm
重量主机 0.4 kg

* Generated by rule engine over the product database; for pre-selection only.

03

Messprinzip

Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

  • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
  • Rockwell C 150 kgf: fast batch checking of hardened parts.
  • Brinell: castings, annealed and coarse-grain materials.
  • Leeb: portable rebound testing on large parts.
04

Process animation

  1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
  2. Mount and align: place the specimen, position the indenter over the test point.
  3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
  4. Load: apply force at the set rate, dwell 10–15 s.
  5. Measure: read diagonals or depth, compute HV/HRC.
  6. Gradient: step along depth and plot hardness versus distance.
0102030405
05

Calculation & formulas

1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

06

Normen

StandardTitleScope
GB/T 4340.1-2009Vickers hardness test — test methodVickers
GB/T 230.1-2018Rockwell hardness testRockwell
GB/T 231.1-2018Brinell hardness testBrinell
ISO 6507-1Vickers hardness testExport
ASTM E92Vickers hardness of metallic materialsAmericas
GB/T 17394.1-2014Leeb hardness testPortable

Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

07

Auswahl

1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

ModelPrincipleRangeTypical use
HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

08

Prüfverfahren

Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

09

Industry applications

  • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
  • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
  • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
  • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
  • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
  • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
  • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
  • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0VergleichTechnischer Vergleich