HMAS-D5/10/30/50SZA Vickers Hardness Tester

Vickers Hardness Tester

ModellHMAS-D5/10/30/50SZA
  • 测量分析系统HMAS‑硬度测量分析系统
  • 光学成像系统维氏硬度大三通光学成像系统
  • 转塔方式自动转塔
  • 升降机构精密梯形丝杆

By submitting you agree to our privacy policy.

01

Überblick

HMAS-D5/10/30/50SZA自动维氏硬度测量分析系统是研润公司新推出的一款高性能硬度测量系统。本机是在传统型的维氏硬度测量功能上新开发的新一代硬度计.该机具有良好的可靠性,可操作性和直观性,是采用精密机械技术、光电技术、和材料硬度测量软件是新型维氏硬度测试仪器。
本机配备了自动运动控制系统:X-Y自动工作平台,可设定位置、距离、平台自动移动,可在行程范围内自由运动的控制方式,不仅仅实现了操作的便利性,同时也为精密尺寸测量(如涂镀层厚度、金相分析及硬度梯等)及金属结构组织分析提供了更正确的分析手段。
HMAS-D5/10/30/50SZA 维氏硬度测量系统适用于测定微小、薄形试件、表面渗镀层等试件的维氏硬度和测定玻璃、陶瓷、玛瑙、宝石等脆性材料的维氏硬度,是科研机构、工厂及质监部门进行材料研究和检测的理想硬度测试仪器。
性能特点:
1、仪器配备高精密的CCD图像成像系统,将仪器内部采集压痕图像转换进入电脑软件中心。
2、本仪器通过电脑控制机器系统,可以在计算机上通过鼠标很方便的完成对硬度计的实时控制,可以实现所有硬度计的相关功能,效果与直接硬度计面板一样。
3、本机配备了自动运动控制系统:X-Y自动工作台,可在行程范围内自由运动的控制方式,不仅仅实现了操作的便利性,同时也为精密尺寸测量(如涂镀层厚度、金相分析及硬度梯度等)及金属结构组织分析提供了更正确的分析手段.
⑴程序控制电动X-Y工作台:移动范围:50×50mm
⑵控制:用测试软件控制
⑶单点压痕或自动连续多点压痕
⑷变速移动:平台移动时,速度可设置
⑸鼠标点动功能:鼠标点哪平台移动到哪
技术参数:
型号
HMAS‑D5/10/30/50SZA
测量分析系统
HMAS‑硬度测量分析系统
光学成像系统
维氏硬度大三通光学成像系统
转塔方式
自动转塔
升降机构
精密梯形丝杆
变荷装置机构
砝码加载
试验力
(5Kg):0.2kgf、0.3kgf、0.5kgf、1kgf、3kgf、5kgf;
(10Kg):0.3kgf、0.5kgf、1kgf、3kgf、5kgf、10kgf;
(30Kg):1kgf、3kgf、5kgf、10kgf、20kgf、30kgf;
(50Kg):1kgf、5kgf、10kgf、20kgf、30kgf、50kgf
转换标尺
HV、HK、HBW、HRA、HRB、HRC、HRD、HRF、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T
聚焦方式
手动
X/Y 平台
自动
Z 轴升降
手动
硬度打压
电脑控制
梯度测试
电脑控制(自动连续打压)
硬度测量
连打连测 + 单点自动 / 手动(多测量系统)
光源调节
电脑控制
长度测量
电脑自动
测试定点
自动导航定位 / 路径自动定位
基点补偿
自动
断裂韧性
软件计算
放大倍数
(21 寸屏) 10X 物镜,总放大倍数约 320X;20X 物镜,总放大倍数约 650 倍
理论硬度测量范围
8‑6000HV
试验力加载
全自动(加载 / 保荷 / 卸载)
执行国家标准
GB/T4340 国家标准,ISO6507 质量认证,ASTM 标准
X‑Y 移动平台
试台尺寸:140*180mm,移动范围 50*50mm,最小步距 0.1μm
硬度值显示方式
(双系统测量) 主机单独测量 / 电脑软件测量分析
读数方式
目镜按钮读数 / 电脑软件读数
计算方式
自动计算
主机最小检测单位
0.12μm (10X 物镜),0.06μm (20X 物镜)
试验力保荷时间
0‑60 秒,最小变动量 1 秒
试件最大高度
150mm
压头中心到内壁距离
170mm
电源电压
AC 220V/50Hz
外形尺寸
220*570*680mm(长 * 宽 * 高)
净重
50.0kg
毛重
67.0kg

HMAS-D5/10/30/50SZA Vickers Hardness Tester supplied by CHWES. 34 key specifications available on request.

02

Technische Daten

测量分析系统HMAS‑硬度测量分析系统
光学成像系统维氏硬度大三通光学成像系统
转塔方式自动转塔
升降机构精密梯形丝杆
变荷装置机构砝码加载
试验力(5Kg):0.2kgf、0.3kgf、0.5kgf、1kgf、3kgf、5kgf;(10Kg):0.3kgf、0.5kgf、1kgf、3kgf、5kgf、10kgf;(30Kg):1kgf、3kgf、5kgf、10kgf、20kgf、30kgf;(50Kg):1kgf、5kgf、10kgf、20kgf、30kgf、50kgf
转换标尺HV、HK、HBW、HRA、HRB、HRC、HRD、HRF、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T
聚焦方式手动
X/Y 平台自动
Z 轴升降手动
硬度打压电脑控制
梯度测试电脑控制(自动连续打压)
硬度测量连打连测 + 单点自动 / 手动(多测量系统)
光源调节电脑控制
长度测量电脑自动
测试定点自动导航定位 / 路径自动定位
基点补偿自动
断裂韧性软件计算
放大倍数(21 寸屏) 10X 物镜,总放大倍数约 320X;20X 物镜,总放大倍数约 650 倍
理论硬度测量范围8‑6000HV
试验力加载全自动(加载 / 保荷 / 卸载)
执行国家标准GB/T4340 国家标准,ISO6507 质量认证,ASTM 标准
X‑Y 移动平台试台尺寸:140*180mm,移动范围 50*50mm,最小步距 0.1μm
硬度值显示方式(双系统测量) 主机单独测量 / 电脑软件测量分析
读数方式目镜按钮读数 / 电脑软件读数
计算方式自动计算
主机最小检测单位0.12μm (10X 物镜),0.06μm (20X 物镜)
试验力保荷时间0‑60 秒,最小变动量 1 秒
试件最大高度150mm
压头中心到内壁距离170mm
电源电压AC 220V/50Hz
外形尺寸220*570*680mm(长 * 宽 * 高)
净重50.0kg
毛重67.0kg

* Generated by rule engine over the product database; for pre-selection only.

03

Messprinzip

Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

  • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
  • Rockwell C 150 kgf: fast batch checking of hardened parts.
  • Brinell: castings, annealed and coarse-grain materials.
  • Leeb: portable rebound testing on large parts.
04

Process animation

  1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
  2. Mount and align: place the specimen, position the indenter over the test point.
  3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
  4. Load: apply force at the set rate, dwell 10–15 s.
  5. Measure: read diagonals or depth, compute HV/HRC.
  6. Gradient: step along depth and plot hardness versus distance.
0102030405
05

Calculation & formulas

1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

06

Normen

StandardTitleScope
GB/T 4340.1-2009Vickers hardness test — test methodVickers
GB/T 230.1-2018Rockwell hardness testRockwell
GB/T 231.1-2018Brinell hardness testBrinell
ISO 6507-1Vickers hardness testExport
ASTM E92Vickers hardness of metallic materialsAmericas
GB/T 17394.1-2014Leeb hardness testPortable

Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

07

Auswahl

1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

ModelPrincipleRangeTypical use
HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

08

Prüfverfahren

Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

09

Industry applications

  • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
  • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
  • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
  • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
  • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
  • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
  • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
  • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0VergleichTechnischer Vergleich