HOTHMAS-D5/10/30/50SZA Vickers Hardness Tester
Vickers Hardness Tester
- 测量分析系统HMAS‑硬度测量分析系统
- 光学成像系统维氏硬度大三通光学成像系统
HBA-1 · 2026-11-17 · +86 21 5748 2007
Hardness Tester
By submitting you agree to our privacy policy.
HBA-1型巴氏硬度计用于检测铝及铝合金材料的硬度。主要用于韦氏硬度计无法检测的厚壁铝合金型材,检测纯铝、较软铝合金、超硬铝合金、铝板、铝棒及铝合金铸件、锻件、压铸件等,还可检测组装后的铝合金制品(铝合金门窗、幕墙、消防梯等),还可用于检测玻璃钢、硬塑料等非金属材料的硬度。
HBA-1型巴氏硬度计符合美国标准ASTM B648-00《巴克尔硬度计测量铝合金硬度的试验方法》和中国标准GB/T3854-2005《增强塑料巴柯尔硬度试验方法》。
仪器特点:
使用方便:单手操作,使用方便,效率高,可在任何场合使用。
灵敏度高:巴氏硬度计有100个刻度,灵敏度远高于韦氏硬度计。
硬度测量范围宽:从纯铝到超硬铝合金均可测试,有效测量范围相当于布氏硬度25~150HBW。
厚度测量范围宽:材料厚度只要大于0.8mm都可测试。
无需支撑:只接触试样一侧即可测试,可测试超大、超宽、超厚材料,测试组装后的铝合金制品。
换算方便:可方便地换算成韦氏、布氏、洛氏、维氏等硬度值。
高质量的压针:压针硬度高、寿命长、互换性好。
技术参数:
量 程:0~100HBa(相当于25~150HBW);
分 辨 率:0.5HBa;
示 值 误 差:42~52HBa ±2HBa;84~88HBa ±1HBa;
重复性误差 :42~52HBa ±2HBa;84~88HBa ±1HBa;
重 量:0.5kg;
巴氏硬度计主要用于测试铝及铝合金。测试铝合金型材、板材、管材主要采用韦氏硬度计,测试纯铝、较软铝合金,超厚铝合金、铝合金棒材及组装后的铝合金制品(例如铝合金门窗、消防梯等)应使用巴氏硬度计。
相关标准:ASTM B648《巴克尔硬度计测量铝合金硬度的试验方法》。
巴氏硬度计还用于测试玻璃钢(玻璃纤维增强塑料)、硬塑料等。
相关标准:GB/T3854-2005《增强塑料巴柯尔硬度试验方法》。ASTM D2583-07《巴氏硬度计测量硬塑料压痕硬度的试验方法》。
巴氏硬度计的改进型可用于较软塑料、很软的金属、皮革、橡胶等
标准配置:
主机;
备用压针(2支);
高值硬度块(1块);
低值硬度块(1块);
校正扳手;
支脚;
仪器箱;
可选附件:
压针;
硬度块(高值、低值);
表头玻璃;
平支脚;
HBA-1 Hardness Tester supplied by CHWES. 6 key specifications available on request.
| 量 程 | 0~100HBa(相当于25~150HBW) |
|---|---|
| 分 辨 率 | 0.5HBa |
| 示 值 误 差 | 42~52HBa ±2HBa;84~88HBa ±1HBa |
| 重复性误差 | 42~52HBa ±2HBa;84~88HBa ±1HBa |
| 重 量 | 0.5kg;巴氏硬度计主要用于测试铝及铝合金;测试铝合金型材、板材、管材主要采用韦氏硬度计,测试纯铝、较软铝合金,超厚铝合金、铝合金棒材及组装后的铝合金制品(例如铝合金门窗、消防梯等)应使用巴氏硬度计 |
| 相关标准 | ASTM B648《巴克尔硬度计测量铝合金硬度的试验方法》;巴氏硬度计还用于测试玻璃钢(玻璃纤维增强塑料)、硬塑料等 |
* Generated by rule engine over the product database; for pre-selection only.
Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.
Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.
1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.
2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.
3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.
4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.
5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.
| Standard | Title | Scope |
|---|---|---|
| GB/T 4340.1-2009 | Vickers hardness test — test method | Vickers |
| GB/T 230.1-2018 | Rockwell hardness test | Rockwell |
| GB/T 231.1-2018 | Brinell hardness test | Brinell |
| ISO 6507-1 | Vickers hardness test | Export |
| ASTM E92 | Vickers hardness of metallic materials | Americas |
| GB/T 17394.1-2014 | Leeb hardness test | Portable |
Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.
1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.
2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.
3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.
4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.
5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.
6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.
| Model | Principle | Range | Typical use |
|---|---|---|---|
| HRC-150SMJ | Rockwell, motorised digital | HRA/HRB/HRC | Batch sampling in heat treatment |
| HRC-150SM / HRC-150M | Rockwell | HRA/HRB/HRC | Incoming and in-process checks |
| HRC-45M | Superficial Rockwell | 15N/30N/45N | Sheet, plating, case layers |
| HRS-150M / XHRS-150M | Digital Rockwell | HRA/HRB/HRC | Lines needing data upload |
| HBRVS-187.5 | Brinell-Vickers-Rockwell | HBW/HRA/HRB/HRC/HV | Mixed low-volume production |
Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.
Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.
Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.
Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.
Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.
Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.