HBA-1 Hardness Tester

Hardness Tester

ModelHBA-1
  • 量 程0~100HBa(相当于25~150HBW)
  • 分 辨 率0.5HBa
  • 示 值 误 差42~52HBa ±2HBa;84~88HBa ±1HBa
  • 重复性误差42~52HBa ±2HBa;84~88HBa ±1HBa

By submitting you agree to our privacy policy.

01

Overview

HBA-1型巴氏硬度计用于检测铝及铝合金材料的硬度。主要用于韦氏硬度计无法检测的厚壁铝合金型材,检测纯铝、较软铝合金、超硬铝合金、铝板、铝棒及铝合金铸件、锻件、压铸件等,还可检测组装后的铝合金制品(铝合金门窗、幕墙、消防梯等),还可用于检测玻璃钢、硬塑料等非金属材料的硬度。
HBA-1型巴氏硬度计符合美国标准ASTM B648-00《巴克尔硬度计测量铝合金硬度的试验方法》和中国标准GB/T3854-2005《增强塑料巴柯尔硬度试验方法》。
仪器特点:
使用方便:单手操作,使用方便,效率高,可在任何场合使用。
灵敏度高:巴氏硬度计有100个刻度,灵敏度远高于韦氏硬度计。
硬度测量范围宽:从纯铝到超硬铝合金均可测试,有效测量范围相当于布氏硬度25~150HBW。
厚度测量范围宽:材料厚度只要大于0.8mm都可测试。
无需支撑:只接触试样一侧即可测试,可测试超大、超宽、超厚材料,测试组装后的铝合金制品。
换算方便:可方便地换算成韦氏、布氏、洛氏、维氏等硬度值。
高质量的压针:压针硬度高、寿命长、互换性好。
技术参数:
量 程:0~100HBa(相当于25~150HBW);
分 辨 率:0.5HBa;
示 值 误 差:42~52HBa ±2HBa;84~88HBa ±1HBa;
重复性误差 :42~52HBa ±2HBa;84~88HBa ±1HBa;
重 量:0.5kg;
巴氏硬度计主要用于测试铝及铝合金。测试铝合金型材、板材、管材主要采用韦氏硬度计,测试纯铝、较软铝合金,超厚铝合金、铝合金棒材及组装后的铝合金制品(例如铝合金门窗、消防梯等)应使用巴氏硬度计。
相关标准:ASTM B648《巴克尔硬度计测量铝合金硬度的试验方法》。
巴氏硬度计还用于测试玻璃钢(玻璃纤维增强塑料)、硬塑料等。
相关标准:GB/T3854-2005《增强塑料巴柯尔硬度试验方法》。ASTM D2583-07《巴氏硬度计测量硬塑料压痕硬度的试验方法》。
巴氏硬度计的改进型可用于较软塑料、很软的金属、皮革、橡胶等
标准配置:
主机;
备用压针(2支);
高值硬度块(1块);
低值硬度块(1块);
校正扳手;
支脚;
仪器箱;
可选附件:
压针;
硬度块(高值、低值);
表头玻璃;
平支脚;

HBA-1 Hardness Tester supplied by CHWES. 6 key specifications available on request.

02

Specifications

量 程0~100HBa(相当于25~150HBW)
分 辨 率0.5HBa
示 值 误 差42~52HBa ±2HBa;84~88HBa ±1HBa
重复性误差42~52HBa ±2HBa;84~88HBa ±1HBa
重 量0.5kg;巴氏硬度计主要用于测试铝及铝合金;测试铝合金型材、板材、管材主要采用韦氏硬度计,测试纯铝、较软铝合金,超厚铝合金、铝合金棒材及组装后的铝合金制品(例如铝合金门窗、消防梯等)应使用巴氏硬度计
相关标准ASTM B648《巴克尔硬度计测量铝合金硬度的试验方法》;巴氏硬度计还用于测试玻璃钢(玻璃纤维增强塑料)、硬塑料等

* Generated by rule engine over the product database; for pre-selection only.

03

Working principle

Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

  • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
  • Rockwell C 150 kgf: fast batch checking of hardened parts.
  • Brinell: castings, annealed and coarse-grain materials.
  • Leeb: portable rebound testing on large parts.
04

Process animation

  1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
  2. Mount and align: place the specimen, position the indenter over the test point.
  3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
  4. Load: apply force at the set rate, dwell 10–15 s.
  5. Measure: read diagonals or depth, compute HV/HRC.
  6. Gradient: step along depth and plot hardness versus distance.
0102030405
05

Calculation & formulas

1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

06

Standards

StandardTitleScope
GB/T 4340.1-2009Vickers hardness test — test methodVickers
GB/T 230.1-2018Rockwell hardness testRockwell
GB/T 231.1-2018Brinell hardness testBrinell
ISO 6507-1Vickers hardness testExport
ASTM E92Vickers hardness of metallic materialsAmericas
GB/T 17394.1-2014Leeb hardness testPortable

Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

07

Selection guide

1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

ModelPrincipleRangeTypical use
HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

08

Test method

Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

09

Industry applications

  • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
  • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
  • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
  • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
  • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
  • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
  • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
  • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0CompareProduct comparison