製品

Profilometers & Roundness Testers

Roughness, profile, cylindricity

CX roughness profilometers, XZ profilometers, Y90 roundness testers and DY cylindricity instruments deliver Ra/Rz and profile elements in one pass; air-bearing spindles reach 0.01 µm class rotation accuracy.

Roughness, profile, cylindricity

Profilometers & Roundness Testers · 21 機種

DYK-300 Cylindricity Measuring Instrument

DYK-300 Cylindricity Measuring Instrument

Cylindricity Measuring Instrument

  • 转台径向旋转综合精度:(±0.03+0.004H )um 轴向旋转综合精度:(±0.03+0.006X )um H:测量高度; X: 到主轴中心的距离 主轴转速:5转/分、10转/分 台面直径:300mm;最大承载:≤70 Kg / 主轴径向旋转综合精度:±0.19 um; 主轴转速:5转/分 台面直径:300mm 最大承载:≤250Kg
  • Z向气浮轴(立柱)0.3um/100mm / 2.5um/全程
01

測定原理

Profilometers & Roundness Testers

A stylus instrument drags a diamond tip (2 or 5 µm radius) across the surface under constant force. The tip follows micro-relief, an inductive transducer converts displacement into a signal, and after amplification and filtering the profile is obtained. Per GB/T 10610 a Gaussian filter (or phase-corrected 2RC) with cut-off λc separates roughness from waviness; Ra, Rz, Rq, Rt and RSm are then computed over the sampling length.

Profile instruments share the same precision guide to capture roughness and macro profile, evaluating straightness, arc radius, angle, groove depth and pitch. Long-travel models (160–300 mm X, ±5 mm Z) suit shafts, rolls and mould surfaces.

  • λc: 0.8 mm for Ra 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm.
  • Force: 0.75 mN typical, below 0.4 mN for soft materials.
  • Direction: normally perpendicular to the machining lay.
02

Process animation

Profilometers & Roundness Testers

  1. Clean and level: wipe with lint-free cloth, align the part to the guide within 1°.
  2. Select cut-off: choose λc from the expected Ra, sampling length usually 5 × λc.
  3. Lower the stylus: automatic descent, zero after the force stabilises.
  4. Traverse: constant speed, acquire the profile.
  5. Filter and compute: Gaussian filter separates roughness, output Ra/Rz/Rq.
  6. Average: three positions per surface.
0102030405
03

Calculation & formulas

Profilometers & Roundness Testers

1. Ra: arithmetic mean deviation, Ra = (1/n)Σ|zi| for sampled points; samples of 2, 4, 3, 5, 1 µm give Ra = 3 µm.

2. Rz: mean of the five highest peaks and five deepest valleys per sampling length (maximum peak-to-valley under GB/T 3505).

3. Rmr: material ratio curve at height c, describing the bearing capability of mating faces.

4. Filtering: Gaussian λc = 0.8/2.5/8 mm separates roughness from waviness; λs suppresses noise.

5. Roundness: least-squares centre, minimum-zone, minimum circumscribed or maximum inscribed; spindle error should be under 1/5 of the tolerance.

04

規格

Profilometers & Roundness Testers

StandardTitleUse
GB/T 1031-2009Surface roughness — parameters and valuesParameter limits
GB/T 3505-2009Surface texture — profile termsTerminology
GB/T 10610-2009Rules and procedures for assessmentFiltering, evaluation
ISO 4287Profile method — termsExport projects
ISO 4288Rules and proceduresSampling length
05

選定ガイド

Profilometers & Roundness Testers

1. Separate three quantities: roughness (Ra/Rz/Rmr, micrometre-scale microtexture), waviness (W, 0.1–10 µm mid-spatial), and form error (roundness, cylindricity, macro geometry). They need different instruments or filters.

2. Profilometers and roundness testers are not interchangeable: profilometers measure Ra/Rz and profile along a line (XZ, CX series); roundness testers measure roundness, cylindricity and coaxiality of bodies of revolution (Y90 series). A cylinder bore needing both requires two machines or a combined type.

3. Sensor range sets capability: ±50 µm suffices for Ra alone; deep grooves, steps and large arcs need ±500 µm or more; mirror surfaces below Ra 0.01 µm need low-noise sensors and isolation.

4. Travel and load: XZ-150 for small parts, XZ-230/XZ-150G for mid-size bores and shafts, Y901200 or custom stages above one metre.

5. Software must support the standards: full Ra/Rz/Rq/Rsk/Rku/Rmr per GB/T 1031 and ISO 4287; roundness per GB/T 7234 with minimum-zone, least-squares, minimum-circumscribed and maximum-inscribed evaluation.

6. On-site use: workshops need vibration and dust control; portable units (DY-300) suit large parts at lower accuracy.

ModelTypeCapabilityTypical parts
XZ-150 / XZ-150GRoughness and profileRa/Rz + profileSmall precision parts
XZ-230Roughness and profileRa/Rz + long travelShafts, cylinder bores
CX-1(S) / CX-1(G)RoughnessRa/Rz/RmrShop-floor sampling
CX-3/100 / CX-3/160Roughness and profileRa + profile + stepsSpools, sealing faces
2207 / 2302ARoundnessRoundness/cylindricityBearing rings, journals
Y9025B/C/DRoundnessRoundness/coaxiality/wavinessPrecision spindles, bores
Y9060 / Y901200Large roundnessLarge-diameter roundnessWind bearings, flanges
DY-300PortableRa/RzLarge parts on site

Why results disagree: wrong cut-off wavelength, insufficient evaluation length, mismatched stylus radius and an unlevelled part account for most disputes.

06

試験方法

Profilometers & Roundness Testers

Preparation. Clean with ethanol to remove oil and chips; let the part stabilise to ambient (±2 °C); inspect the stylus at 20× for wear.

Settings. Choose λc to GB/T 1031 from expected Ra: 0.25 mm up to 0.1 µm, 0.8 mm for 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm; evaluation length 5 × λc.

Measurement. Stylus perpendicular to the lay, lower slowly, start when force is stable. Measure at least three positions per surface and average; on cylinders follow the generatrix.

Judgement. Compare with the drawing limit; no single reading should exceed 1.2 × the limit. Arbitrate with a profile instrument and a certified specimen.

Quality control. Daily check against Ra 0.4/1.6/6.3 specimens, recalibrate beyond 5% deviation, replace or verify the stylus every 12 months.

07

Industry applications

Profilometers & Roundness Testers

  • Hydraulics and pneumatics: Ra/Rz and Rmr on spools, cylinder bores and valve blocks, governing leakage and oil-film load capacity.
  • Bearings and spindles: raceway roundness, cylindricity and waviness, the latter being the main source of vibration and noise.
  • Engines and transmissions: bore roundness and cylindricity, crank-journal roundness, big-end bore form error.
  • Sealing faces: O-ring groove roughness and flange waviness affecting seal reliability.
  • Optics and semiconductors: Ra ≤0.005 µm, flatness and waviness requiring high-resolution sensors and isolation.
  • Moulds: cavity polish Ra and draft-face texture direction, affecting release and appearance.
  • Additive manufacturing: as-built Ra and support residue for post-processing validation.
  • Tools and coatings: edge honing radius and its correlation with coating roughness and adhesion.
導入事例

導入事例

すべて見る→

Price and lead time for this model

技術者が 1 営業日以内に選定案・検査基準・納期をご提案します。

⇄0比較仕様比較