XC-150 Surface Roughness Tester

Surface Roughness Tester

型番XC-150
  • 1.测量范围Z向测量最大高度:200mm
  • X向测量最大行程150mm
  • Z向测量最小内径φ10mm
  • 2.表面粗糙度评价Ra0.01um-10um

By submitting you agree to our privacy policy.

01

製品概要

XC型形状粗糙度测量仪,是测量轮廓形状及表面粗糙度的一体机,具备分析测量轮廓形状和表面粗糙度的强大功能。实现尺寸、形状、粗糙度三个要素的正确测量。用于测量各种零件的直线度、倾斜度、角度处理、圆度处理、双沟处理、双圆弧处理等机械零件表面微观几何结构和宏观几何形状的参数。该系统采用进口扇形光栅采集数据,测量量程大、精度高,整体系统装调方便、操作简单、测量效率高。适用于机械加工、汽车、摩托车、精密五金、精密工具、模具、刀具、光学元件等行业。
系统特征:
1、高性能、高配置形状粗糙度一体机,可进行形状和粗糙度测量,方便用户一次性测量要求。
2、X轴方向采用进口高精度滑动导轨作为水平移动的可靠基准,并采用进口高精度光栅技术进行移动测量。
3、Z轴方向采用滚珠丝杠传动系统电机驱动,自动操作,方便可靠。
4、传感器采用高精度智能编码器旋转光栅尺,测量量程大,精度高,稳定性更强。
5、测量软件采用Windows平台,自主研发,兼容Winxp、Win7、Win8测量参数按照国标参数定义执行。
6、测量工作台可进行Y方向、水平面扇形方向调整及各种角度调整,测量传感器机构可根据工件情况进行倾斜角度测量,极大的满足用户测量需求。
7、标准样块采用光学玻璃基体,不易划伤。标准样块经国家计量院检定,精度可靠,使用寿命长。
8、测量功能强大,图形显示、打印直观、便捷,数学模型完整。
技术参数:
1.测量范围:Z向测量最大高度:200mm;X向测量最大行程:150mm;Z向测量最小内径:φ10mm;
2.表面粗糙度评价:Ra0.01um-10um;
3.光栅尺分辨率:0.1um;
4.光栅尺定位精度:±(1+2L/100)um;
5.传感器量程:±40um;±20mm;
6.传感器分辨率:0.0195um;
7.移动速度:Z轴(立柱):1-15mm/S;X轴(横向测量速度):0.05、0.2、0.4、0.8(mm/S);
8.测针针尖半径:2um;0.5mm、20um;
9.测针测力:1mN;30mN;
10.测臂长度:150mm、200mm;
11.测臂直径:6mm;
12.驱动箱移动直线度:2um/100mm(直线导轨);
13.驱动箱倾斜角度:±15度;
14.主机材质:大理石;
15.主机重量:600kg;
16.主机尺寸:910*560*1430;

XC-150 Surface Roughness Tester supplied by CHWES. 19 key specifications available on request.

02

仕様

1.测量范围Z向测量最大高度:200mm
X向测量最大行程150mm
Z向测量最小内径φ10mm
2.表面粗糙度评价Ra0.01um-10um
3.光栅尺分辨率0.1um
4.光栅尺定位精度±(1+2L/100)um
5.传感器量程±40um;±20mm
6.传感器分辨率0.0195um
7.移动速度Z轴(立柱):1-15mm/S
X轴(横向测量速度)0.;0.;0.;0.8(mm/S)
8.测针针尖半径2um;0.5mm、20um
9.测针测力1mN;30mN
10.测臂长度150mm、200mm
11.测臂直径6mm
12.驱动箱移动直线度2um/100mm(直线导轨)
13.驱动箱倾斜角度±15度
14.主机材质大理石
15.主机重量600kg
16.主机尺寸910*560*1430

* Generated by rule engine over the product database; for pre-selection only.

03

測定原理

A stylus instrument drags a diamond tip (2 or 5 µm radius) across the surface under constant force. The tip follows micro-relief, an inductive transducer converts displacement into a signal, and after amplification and filtering the profile is obtained. Per GB/T 10610 a Gaussian filter (or phase-corrected 2RC) with cut-off λc separates roughness from waviness; Ra, Rz, Rq, Rt and RSm are then computed over the sampling length.

Profile instruments share the same precision guide to capture roughness and macro profile, evaluating straightness, arc radius, angle, groove depth and pitch. Long-travel models (160–300 mm X, ±5 mm Z) suit shafts, rolls and mould surfaces.

  • λc: 0.8 mm for Ra 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm.
  • Force: 0.75 mN typical, below 0.4 mN for soft materials.
  • Direction: normally perpendicular to the machining lay.
04

Process animation

  1. Clean and level: wipe with lint-free cloth, align the part to the guide within 1°.
  2. Select cut-off: choose λc from the expected Ra, sampling length usually 5 × λc.
  3. Lower the stylus: automatic descent, zero after the force stabilises.
  4. Traverse: constant speed, acquire the profile.
  5. Filter and compute: Gaussian filter separates roughness, output Ra/Rz/Rq.
  6. Average: three positions per surface.
0102030405
05

Calculation & formulas

1. Ra: arithmetic mean deviation, Ra = (1/n)Σ|zi| for sampled points; samples of 2, 4, 3, 5, 1 µm give Ra = 3 µm.

2. Rz: mean of the five highest peaks and five deepest valleys per sampling length (maximum peak-to-valley under GB/T 3505).

3. Rmr: material ratio curve at height c, describing the bearing capability of mating faces.

4. Filtering: Gaussian λc = 0.8/2.5/8 mm separates roughness from waviness; λs suppresses noise.

5. Roundness: least-squares centre, minimum-zone, minimum circumscribed or maximum inscribed; spindle error should be under 1/5 of the tolerance.

06

規格

StandardTitleUse
GB/T 1031-2009Surface roughness — parameters and valuesParameter limits
GB/T 3505-2009Surface texture — profile termsTerminology
GB/T 10610-2009Rules and procedures for assessmentFiltering, evaluation
ISO 4287Profile method — termsExport projects
ISO 4288Rules and proceduresSampling length
07

選定ガイド

1. Separate three quantities: roughness (Ra/Rz/Rmr, micrometre-scale microtexture), waviness (W, 0.1–10 µm mid-spatial), and form error (roundness, cylindricity, macro geometry). They need different instruments or filters.

2. Profilometers and roundness testers are not interchangeable: profilometers measure Ra/Rz and profile along a line (XZ, CX series); roundness testers measure roundness, cylindricity and coaxiality of bodies of revolution (Y90 series). A cylinder bore needing both requires two machines or a combined type.

3. Sensor range sets capability: ±50 µm suffices for Ra alone; deep grooves, steps and large arcs need ±500 µm or more; mirror surfaces below Ra 0.01 µm need low-noise sensors and isolation.

4. Travel and load: XZ-150 for small parts, XZ-230/XZ-150G for mid-size bores and shafts, Y901200 or custom stages above one metre.

5. Software must support the standards: full Ra/Rz/Rq/Rsk/Rku/Rmr per GB/T 1031 and ISO 4287; roundness per GB/T 7234 with minimum-zone, least-squares, minimum-circumscribed and maximum-inscribed evaluation.

6. On-site use: workshops need vibration and dust control; portable units (DY-300) suit large parts at lower accuracy.

ModelTypeCapabilityTypical parts
XZ-150 / XZ-150GRoughness and profileRa/Rz + profileSmall precision parts
XZ-230Roughness and profileRa/Rz + long travelShafts, cylinder bores
CX-1(S) / CX-1(G)RoughnessRa/Rz/RmrShop-floor sampling
CX-3/100 / CX-3/160Roughness and profileRa + profile + stepsSpools, sealing faces
2207 / 2302ARoundnessRoundness/cylindricityBearing rings, journals
Y9025B/C/DRoundnessRoundness/coaxiality/wavinessPrecision spindles, bores
Y9060 / Y901200Large roundnessLarge-diameter roundnessWind bearings, flanges
DY-300PortableRa/RzLarge parts on site

Why results disagree: wrong cut-off wavelength, insufficient evaluation length, mismatched stylus radius and an unlevelled part account for most disputes.

08

試験方法

Preparation. Clean with ethanol to remove oil and chips; let the part stabilise to ambient (±2 °C); inspect the stylus at 20× for wear.

Settings. Choose λc to GB/T 1031 from expected Ra: 0.25 mm up to 0.1 µm, 0.8 mm for 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm; evaluation length 5 × λc.

Measurement. Stylus perpendicular to the lay, lower slowly, start when force is stable. Measure at least three positions per surface and average; on cylinders follow the generatrix.

Judgement. Compare with the drawing limit; no single reading should exceed 1.2 × the limit. Arbitrate with a profile instrument and a certified specimen.

Quality control. Daily check against Ra 0.4/1.6/6.3 specimens, recalibrate beyond 5% deviation, replace or verify the stylus every 12 months.

09

Industry applications

  • Hydraulics and pneumatics: Ra/Rz and Rmr on spools, cylinder bores and valve blocks, governing leakage and oil-film load capacity.
  • Bearings and spindles: raceway roundness, cylindricity and waviness, the latter being the main source of vibration and noise.
  • Engines and transmissions: bore roundness and cylindricity, crank-journal roundness, big-end bore form error.
  • Sealing faces: O-ring groove roughness and flange waviness affecting seal reliability.
  • Optics and semiconductors: Ra ≤0.005 µm, flatness and waviness requiring high-resolution sensors and isolation.
  • Moulds: cavity polish Ra and draft-face texture direction, affecting release and appearance.
  • Additive manufacturing: as-built Ra and support residue for post-processing validation.
  • Tools and coatings: edge honing radius and its correlation with coating roughness and adhesion.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0比較仕様比較