XZ-150 Surface Contour Measuring Instrument

Surface Contour Measuring Instrument

型番XZ-150
  • 测量 范围轴 / mm / Φ1~Φ100
  • 套mm / ≤Φ200
  • 最大加工长度mm / 140
  • 气浮 工作台X轴导轨移动直线度 / μm/m / 0.3/80

By submitting you agree to our privacy policy.

01

製品概要

一、XZ-150轮廓仪-形状测量仪应用范围:
XZ-150轮廓仪-形状测量仪该型仪器可测量各种机械零件的素线和截面轮廓形状参数,可测量各种零件的直线度、倾斜角、角度、凸度、曲率半径、沟心距、槽宽、槽深等。在轴承行业中可测量各种零件的直线度、平行度、倾斜度、角度处理、圆处理(直线到切线的距离、圆心到圆心距离、圆弧半径、交点到圆的心距离、圆心到直线距离)、点线处理(交点到直线距离、交点到圆心距离、两直线交点、交点与交点距离)、对数曲线、槽宽、槽深、沟边距、沟心距、倾斜度、水平距离、垂直距离等形状参数。
二、XZ-150轮廓仪-形状测量仪主要特点:
2.1 具有XZ-230型仪器的检测功能,体积小、成本低,较适合中小型企业;
2.2直线运动导轨采用精密气浮导轨,精度保持长久,直线移动精度高,仪器使用寿命长;
2.3直线运动导轨位移数据采集采用精密直线光栅,定位精度高,稳定性好;
2.4仪器采用WINDOWS系统操作平台,专业测量软件,测量界面简洁直观,操作便捷;可以实时显示图形数据、存盘留档、随时打印,图形分析报告,直观清晰;
2.5测量结果可根据标注需要任意旋转。
2.6强大的误差补偿功能,使测量结果更精确;
2.7测量操作设置鼠标和键盘快捷操作,用户可根据操作习惯自由选择;
2.8设计特殊装配夹具,方便工件的装夹调整,大大提高了测量效率;
2.9使用范围广,测量范围大;
三、仪器技术参数
名称
单位
参数
备注
测量
范围
轴
mm
Φ1~Φ100
套
mm
≤Φ200
最大加工长度
mm
140
气浮
工作台
X轴导轨移动直线度
μm/m
0.3/80
X轴移动距离精度
(光栅尺国产)
分辨率
μm
1μm
精度
mm
5μm/全行程
承重
kg
50
X轴(工作台水平横向移动)
mm
140
传感器
测针上下移动(量程)
mm
6
量程与分辨率之比
1/65536
其它
测量精度(半径误差)
%
0.1~1
重复测量精度
%
3
测量速度
mm/s
0.2~0.4
分3档选择
电源
kW
0.5
220V,50Hz
气源压力
MPa
≥0.5

XZ-150 Surface Contour Measuring Instrument supplied by CHWES. 15 key specifications available on request.

02

仕様

测量 范围轴 / mm / Φ1~Φ100
套mm / ≤Φ200
最大加工长度mm / 140
气浮 工作台X轴导轨移动直线度 / μm/m / 0.3/80
X轴移动距离精度 (光栅尺国产)分辨率 / μm / 1μm
精度mm / 5μm/全行程
承重kg / 50
X轴(工作台水平横向移动)mm / 140
传感器测针上下移动(量程) / mm / 6
量程与分辨率之比1/65536
其它测量精度(半径误差) / % / 0.1~1
重复测量精度% / 3
测量速度mm/s / 0.2~0.4 / 分3档选择
电源kW / 0.5 / 220V,50Hz
气源压力MPa / ≥0.5

* Generated by rule engine over the product database; for pre-selection only.

03

測定原理

A stylus instrument drags a diamond tip (2 or 5 µm radius) across the surface under constant force. The tip follows micro-relief, an inductive transducer converts displacement into a signal, and after amplification and filtering the profile is obtained. Per GB/T 10610 a Gaussian filter (or phase-corrected 2RC) with cut-off λc separates roughness from waviness; Ra, Rz, Rq, Rt and RSm are then computed over the sampling length.

Profile instruments share the same precision guide to capture roughness and macro profile, evaluating straightness, arc radius, angle, groove depth and pitch. Long-travel models (160–300 mm X, ±5 mm Z) suit shafts, rolls and mould surfaces.

  • λc: 0.8 mm for Ra 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm.
  • Force: 0.75 mN typical, below 0.4 mN for soft materials.
  • Direction: normally perpendicular to the machining lay.
04

Process animation

  1. Clean and level: wipe with lint-free cloth, align the part to the guide within 1°.
  2. Select cut-off: choose λc from the expected Ra, sampling length usually 5 × λc.
  3. Lower the stylus: automatic descent, zero after the force stabilises.
  4. Traverse: constant speed, acquire the profile.
  5. Filter and compute: Gaussian filter separates roughness, output Ra/Rz/Rq.
  6. Average: three positions per surface.
0102030405
05

Calculation & formulas

1. Ra: arithmetic mean deviation, Ra = (1/n)Σ|zi| for sampled points; samples of 2, 4, 3, 5, 1 µm give Ra = 3 µm.

2. Rz: mean of the five highest peaks and five deepest valleys per sampling length (maximum peak-to-valley under GB/T 3505).

3. Rmr: material ratio curve at height c, describing the bearing capability of mating faces.

4. Filtering: Gaussian λc = 0.8/2.5/8 mm separates roughness from waviness; λs suppresses noise.

5. Roundness: least-squares centre, minimum-zone, minimum circumscribed or maximum inscribed; spindle error should be under 1/5 of the tolerance.

06

規格

StandardTitleUse
GB/T 1031-2009Surface roughness — parameters and valuesParameter limits
GB/T 3505-2009Surface texture — profile termsTerminology
GB/T 10610-2009Rules and procedures for assessmentFiltering, evaluation
ISO 4287Profile method — termsExport projects
ISO 4288Rules and proceduresSampling length
07

選定ガイド

1. Separate three quantities: roughness (Ra/Rz/Rmr, micrometre-scale microtexture), waviness (W, 0.1–10 µm mid-spatial), and form error (roundness, cylindricity, macro geometry). They need different instruments or filters.

2. Profilometers and roundness testers are not interchangeable: profilometers measure Ra/Rz and profile along a line (XZ, CX series); roundness testers measure roundness, cylindricity and coaxiality of bodies of revolution (Y90 series). A cylinder bore needing both requires two machines or a combined type.

3. Sensor range sets capability: ±50 µm suffices for Ra alone; deep grooves, steps and large arcs need ±500 µm or more; mirror surfaces below Ra 0.01 µm need low-noise sensors and isolation.

4. Travel and load: XZ-150 for small parts, XZ-230/XZ-150G for mid-size bores and shafts, Y901200 or custom stages above one metre.

5. Software must support the standards: full Ra/Rz/Rq/Rsk/Rku/Rmr per GB/T 1031 and ISO 4287; roundness per GB/T 7234 with minimum-zone, least-squares, minimum-circumscribed and maximum-inscribed evaluation.

6. On-site use: workshops need vibration and dust control; portable units (DY-300) suit large parts at lower accuracy.

ModelTypeCapabilityTypical parts
XZ-150 / XZ-150GRoughness and profileRa/Rz + profileSmall precision parts
XZ-230Roughness and profileRa/Rz + long travelShafts, cylinder bores
CX-1(S) / CX-1(G)RoughnessRa/Rz/RmrShop-floor sampling
CX-3/100 / CX-3/160Roughness and profileRa + profile + stepsSpools, sealing faces
2207 / 2302ARoundnessRoundness/cylindricityBearing rings, journals
Y9025B/C/DRoundnessRoundness/coaxiality/wavinessPrecision spindles, bores
Y9060 / Y901200Large roundnessLarge-diameter roundnessWind bearings, flanges
DY-300PortableRa/RzLarge parts on site

Why results disagree: wrong cut-off wavelength, insufficient evaluation length, mismatched stylus radius and an unlevelled part account for most disputes.

08

試験方法

Preparation. Clean with ethanol to remove oil and chips; let the part stabilise to ambient (±2 °C); inspect the stylus at 20× for wear.

Settings. Choose λc to GB/T 1031 from expected Ra: 0.25 mm up to 0.1 µm, 0.8 mm for 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm; evaluation length 5 × λc.

Measurement. Stylus perpendicular to the lay, lower slowly, start when force is stable. Measure at least three positions per surface and average; on cylinders follow the generatrix.

Judgement. Compare with the drawing limit; no single reading should exceed 1.2 × the limit. Arbitrate with a profile instrument and a certified specimen.

Quality control. Daily check against Ra 0.4/1.6/6.3 specimens, recalibrate beyond 5% deviation, replace or verify the stylus every 12 months.

09

Industry applications

  • Hydraulics and pneumatics: Ra/Rz and Rmr on spools, cylinder bores and valve blocks, governing leakage and oil-film load capacity.
  • Bearings and spindles: raceway roundness, cylindricity and waviness, the latter being the main source of vibration and noise.
  • Engines and transmissions: bore roundness and cylindricity, crank-journal roundness, big-end bore form error.
  • Sealing faces: O-ring groove roughness and flange waviness affecting seal reliability.
  • Optics and semiconductors: Ra ≤0.005 µm, flatness and waviness requiring high-resolution sensors and isolation.
  • Moulds: cavity polish Ra and draft-face texture direction, affecting release and appearance.
  • Additive manufacturing: as-built Ra and support residue for post-processing validation.
  • Tools and coatings: edge honing radius and its correlation with coating roughness and adhesion.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0比較仕様比較