MARSURF-XC2 Surface Roughness Tester

Surface Roughness Tester

型番MARSURF-XC2
  • 测杆长度175 mm, 350 mm
  • 测量速度(文本)0.2 mm/s 至 4 mm/s
  • 针尖半径25 μm
  • 扫描长度末尾(X 方向)120 mm

By submitting you agree to our privacy policy.

01

製品概要

MARSURF XC 2 MIT CD 120轮廓测量站是精密轮廓测量入门之选
测量和评估工件和工具上与功能相关的几何参数是研究、设计和工业的基本要求。相对其他方法,快速、简单而经济的 2D 轮廓测量系统受到越来越多的青睐。MarSurf XC 2 可满足精度和评估标准范围相关的各方面需求。同时,它还能提供安全而可靠的结果。
利用相关元件,更换基准元件后可立即对基准元件相关的参数重新计算。
密码保护用户访问权限,避免不当使用
以多年经验为基础的出色校准流程,包括几何形状校准、测量力校准、弯曲补偿等等
稳定、坚固的测头
平滑运行,稳定而准确的驱动装置
根据各种调整速度自动降低和抬高测杆
高定位精度
测杆固定技术,防碰撞保护
MARSURF-XC2表面粗糙度轮廓仪的应用:
1.机器建造:轴承、螺纹、螺纹柱、滚珠丝杠、轴、支架、阀门
2.生产领域最需要的测量:部分自动流程中的轮廓测量
3.汽车业:转向、刹车系统、变速箱、曲轴、凸轮轴、气缸盖
4.医疗:髋关节和膝关节内用假体的轮廓测量,医用螺丝的轮廓测量,种植牙的轮廓测量
MARSURF-XC2表面粗糙度轮廓仪技术参数:
接触速度(Z 方向)
0.1 至 1 mm/s
测杆长度
175 mm, 350 mm
测量速度(文本)
0.2 mm/s 至 4 mm/s
针尖半径
25 μm
扫描长度末尾(X 方向)
120 mm
分辨率
Z 方向,相对探针针头:0.38 μm(350 mm 测杆)/ 0.19 μm(175 mm 测杆)
在 Z 方向,相对于测量系统:0.04 μm
扫描长度开始(X 方向)
0.2 mm
取样角
在平滑表面上,取决于偏差:后缘高至 88°,前缘高至 77°
定位速度(文本)
X 方向返回速度:0.2 至 8 mm/s
Z 方向:0.2 至 10 mm/s
导块偏差
< 1 μm(超过 120 mm)
测量范围 mm
(Z 方向)50 mm
扫描长度(文本)
0.2 mm 至 120 mm
测量力 (N)
1 mN 至 120 mN

MARSURF-XC2 Surface Roughness Tester supplied by CHWES. 12 key specifications available on request.

02

仕様

测杆长度175 mm, 350 mm
测量速度(文本)0.2 mm/s 至 4 mm/s
针尖半径25 μm
扫描长度末尾(X 方向)120 mm
分辨率Z 方向,相对探针针头:0.38 μm(350 mm 测杆)/ 0.19 μm(175 mm 测杆) 在 Z 方向,相对于测量系统:0.04 μm
扫描长度开始(X 方向)0.2 mm
取样角在平滑表面上,取决于偏差:后缘高至 88°,前缘高至 77°
定位速度(文本)X 方向返回速度:0.2 至 8 mm/s Z 方向:0.2 至 10 mm/s
导块偏差< 1 μm(超过 120 mm)
测量范围 mm(Z 方向)50 mm
扫描长度(文本)0.2 mm 至 120 mm
测量力 (N)1 mN 至 120 mN

* Generated by rule engine over the product database; for pre-selection only.

03

測定原理

A stylus instrument drags a diamond tip (2 or 5 µm radius) across the surface under constant force. The tip follows micro-relief, an inductive transducer converts displacement into a signal, and after amplification and filtering the profile is obtained. Per GB/T 10610 a Gaussian filter (or phase-corrected 2RC) with cut-off λc separates roughness from waviness; Ra, Rz, Rq, Rt and RSm are then computed over the sampling length.

Profile instruments share the same precision guide to capture roughness and macro profile, evaluating straightness, arc radius, angle, groove depth and pitch. Long-travel models (160–300 mm X, ±5 mm Z) suit shafts, rolls and mould surfaces.

  • λc: 0.8 mm for Ra 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm.
  • Force: 0.75 mN typical, below 0.4 mN for soft materials.
  • Direction: normally perpendicular to the machining lay.
04

Process animation

  1. Clean and level: wipe with lint-free cloth, align the part to the guide within 1°.
  2. Select cut-off: choose λc from the expected Ra, sampling length usually 5 × λc.
  3. Lower the stylus: automatic descent, zero after the force stabilises.
  4. Traverse: constant speed, acquire the profile.
  5. Filter and compute: Gaussian filter separates roughness, output Ra/Rz/Rq.
  6. Average: three positions per surface.
0102030405
05

Calculation & formulas

1. Ra: arithmetic mean deviation, Ra = (1/n)Σ|zi| for sampled points; samples of 2, 4, 3, 5, 1 µm give Ra = 3 µm.

2. Rz: mean of the five highest peaks and five deepest valleys per sampling length (maximum peak-to-valley under GB/T 3505).

3. Rmr: material ratio curve at height c, describing the bearing capability of mating faces.

4. Filtering: Gaussian λc = 0.8/2.5/8 mm separates roughness from waviness; λs suppresses noise.

5. Roundness: least-squares centre, minimum-zone, minimum circumscribed or maximum inscribed; spindle error should be under 1/5 of the tolerance.

06

規格

StandardTitleUse
GB/T 1031-2009Surface roughness — parameters and valuesParameter limits
GB/T 3505-2009Surface texture — profile termsTerminology
GB/T 10610-2009Rules and procedures for assessmentFiltering, evaluation
ISO 4287Profile method — termsExport projects
ISO 4288Rules and proceduresSampling length
07

選定ガイド

1. Separate three quantities: roughness (Ra/Rz/Rmr, micrometre-scale microtexture), waviness (W, 0.1–10 µm mid-spatial), and form error (roundness, cylindricity, macro geometry). They need different instruments or filters.

2. Profilometers and roundness testers are not interchangeable: profilometers measure Ra/Rz and profile along a line (XZ, CX series); roundness testers measure roundness, cylindricity and coaxiality of bodies of revolution (Y90 series). A cylinder bore needing both requires two machines or a combined type.

3. Sensor range sets capability: ±50 µm suffices for Ra alone; deep grooves, steps and large arcs need ±500 µm or more; mirror surfaces below Ra 0.01 µm need low-noise sensors and isolation.

4. Travel and load: XZ-150 for small parts, XZ-230/XZ-150G for mid-size bores and shafts, Y901200 or custom stages above one metre.

5. Software must support the standards: full Ra/Rz/Rq/Rsk/Rku/Rmr per GB/T 1031 and ISO 4287; roundness per GB/T 7234 with minimum-zone, least-squares, minimum-circumscribed and maximum-inscribed evaluation.

6. On-site use: workshops need vibration and dust control; portable units (DY-300) suit large parts at lower accuracy.

ModelTypeCapabilityTypical parts
XZ-150 / XZ-150GRoughness and profileRa/Rz + profileSmall precision parts
XZ-230Roughness and profileRa/Rz + long travelShafts, cylinder bores
CX-1(S) / CX-1(G)RoughnessRa/Rz/RmrShop-floor sampling
CX-3/100 / CX-3/160Roughness and profileRa + profile + stepsSpools, sealing faces
2207 / 2302ARoundnessRoundness/cylindricityBearing rings, journals
Y9025B/C/DRoundnessRoundness/coaxiality/wavinessPrecision spindles, bores
Y9060 / Y901200Large roundnessLarge-diameter roundnessWind bearings, flanges
DY-300PortableRa/RzLarge parts on site

Why results disagree: wrong cut-off wavelength, insufficient evaluation length, mismatched stylus radius and an unlevelled part account for most disputes.

08

試験方法

Preparation. Clean with ethanol to remove oil and chips; let the part stabilise to ambient (±2 °C); inspect the stylus at 20× for wear.

Settings. Choose λc to GB/T 1031 from expected Ra: 0.25 mm up to 0.1 µm, 0.8 mm for 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm; evaluation length 5 × λc.

Measurement. Stylus perpendicular to the lay, lower slowly, start when force is stable. Measure at least three positions per surface and average; on cylinders follow the generatrix.

Judgement. Compare with the drawing limit; no single reading should exceed 1.2 × the limit. Arbitrate with a profile instrument and a certified specimen.

Quality control. Daily check against Ra 0.4/1.6/6.3 specimens, recalibrate beyond 5% deviation, replace or verify the stylus every 12 months.

09

Industry applications

  • Hydraulics and pneumatics: Ra/Rz and Rmr on spools, cylinder bores and valve blocks, governing leakage and oil-film load capacity.
  • Bearings and spindles: raceway roundness, cylindricity and waviness, the latter being the main source of vibration and noise.
  • Engines and transmissions: bore roundness and cylindricity, crank-journal roundness, big-end bore form error.
  • Sealing faces: O-ring groove roughness and flange waviness affecting seal reliability.
  • Optics and semiconductors: Ra ≤0.005 µm, flatness and waviness requiring high-resolution sensors and isolation.
  • Moulds: cavity polish Ra and draft-face texture direction, affecting release and appearance.
  • Additive manufacturing: as-built Ra and support residue for post-processing validation.
  • Tools and coatings: edge honing radius and its correlation with coating roughness and adhesion.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0比較仕様比較