DYK-300 Cylindricity Measuring Instrument

Cylindricity Measuring Instrument

型番DYK-300
  • 转台径向旋转综合精度:(±0.03+0.004H )um 轴向旋转综合精度:(±0.03+0.006X )um H:测量高度; X: 到主轴中心的距离 主轴转速:5转/分、10转/分 台面直径:300mm;最大承载:≤70 Kg / 主轴径向旋转综合精度:±0.19 um; 主轴转速:5转/分 台面直径:300mm 最大承载:≤250Kg
  • Z向气浮轴(立柱)0.3um/100mm / 2.5um/全程
  • X向气浮轴(横臂)0.5um/100mm / 3um/全程
  • Y向气浮轴5um/全程

By submitting you agree to our privacy policy.

01

製品概要

DYK-300桥式圆柱度仪主要用于测量各种规则、不规则的表面连续或间断的回转体工件的圆度、圆柱度、直线度、同心度、同轴度、平面度、平行度、垂直度、表面波纹度等的测量,并可对工件进行频谱分析、波高分析、偏心、轴弯曲度分析、跳动量分析等。广泛应用于汽车零部件、轴承、电机、汽配、轴承、机床、纺织配件、油嘴油泵、航空航天等精密机械制造企业,科研院所、大专院校、计量机构。
1、DY-300主要特点:
1.1高精度的回转测量转台采用空气静压轴承结构,仪器主轴精度高不磨损,使用寿命长;
1.2数据采集采用德国HEIDENHAIN公司进口精密圆光栅及相关技术,定位精确,稳定性好;
1.3仪器采用WINDOWS系统操作平台,专业测量软件,测量界面简洁直观,操作便捷;可以实时显示图形数据、存盘留档、随时打印,图形分析报告,直观清晰;
1.4根据工件测量需求,自动调整传感器测头方向;
1.5具备自动识别功能与凹口剔除方案功能,并能对圆柱某一界面进行提取,识别其圆度情况。
2、DYK-300主要特点:
2.1高精度的回转测量转台采用空气静压轴承结构,仪器主轴精度高不磨损,使用寿命长;
2.2采用先进的直流伺服电机,无框电机做为驱动机构与高分辨率进口开式光栅尺通过运动控制器的闭环控制保证三直线轴定位精确,主轴旋转平稳。
2.3X、Y、Z三个方向直线运动整体机械结构采用龙门框架式结构。解决大尺寸、深孔,非标产品的测量要求。
2.4数据采集采用进口高分辨率圆光栅和直线光栅,完成圆度、圆柱度测量,定位精确,稳定性好。
2.5专业测量软件,测量界面简洁直观,操作便捷。
主要参数:
型号、项目
DY-300
DYK-300
转台
径向旋转综合精度:(±0.03+0.004H )um
轴向旋转综合精度:(±0.03+0.006X )um
H:测量高度; X: 到主轴中心的距离
主轴转速:5转/分、10转/分
台面直径:300mm;最大承载:≤70 Kg
主轴径向旋转综合精度:±0.19 um;
主轴转速:5转/分
台面直径:300mm
最大承载:≤250Kg
Z向气浮轴(立柱)
0.3um/100mm
2.5um/全程
X向气浮轴(横臂)
0.5um/100mm
3um/全程
Y向气浮轴
5um/全程
立柱与回转轴线的平行度
0.45um/100mm
0.5um/100mm
最大测量高度
500mm
≤1200mm
最大测量孔深度
70mm(使用标准测针时)
孔径≥110mm时,检测深度≤1100mm
最大测量直径
Ф300mm
传感器
测量范围:±250mm;测力:7-10Mn;测针:Ф2.0mm(宝石球测针)
圆度评定方法
LSC/MZC/MIC/MCC
测量分析功能
圆度、圆柱度、直线度、同心度、同轴度、平面度、平行度、垂直度、直径、锥度、表面波纹度、跳动量、波段分析、偏心、频谱分析

DYK-300 Cylindricity Measuring Instrument supplied by CHWES. 11 key specifications available on request.

02

仕様

转台径向旋转综合精度:(±0.03+0.004H )um 轴向旋转综合精度:(±0.03+0.006X )um H:测量高度; X: 到主轴中心的距离 主轴转速:5转/分、10转/分 台面直径:300mm;最大承载:≤70 Kg / 主轴径向旋转综合精度:±0.19 um; 主轴转速:5转/分 台面直径:300mm 最大承载:≤250Kg
Z向气浮轴(立柱)0.3um/100mm / 2.5um/全程
X向气浮轴(横臂)0.5um/100mm / 3um/全程
Y向气浮轴5um/全程
立柱与回转轴线的平行度0.45um/100mm / 0.5um/100mm
最大测量高度500mm / ≤1200mm
最大测量孔深度70mm(使用标准测针时) / 孔径≥110mm时,检测深度≤1100mm
最大测量直径Ф300mm
传感器测量范围:±250mm;测力:7-10Mn;测针:Ф2.0mm(宝石球测针)
圆度评定方法LSC/MZC/MIC/MCC
测量分析功能圆度、圆柱度、直线度、同心度、同轴度、平面度、平行度、垂直度、直径、锥度、表面波纹度、跳动量、波段分析、偏心、频谱分析

* Generated by rule engine over the product database; for pre-selection only.

03

測定原理

A stylus instrument drags a diamond tip (2 or 5 µm radius) across the surface under constant force. The tip follows micro-relief, an inductive transducer converts displacement into a signal, and after amplification and filtering the profile is obtained. Per GB/T 10610 a Gaussian filter (or phase-corrected 2RC) with cut-off λc separates roughness from waviness; Ra, Rz, Rq, Rt and RSm are then computed over the sampling length.

Profile instruments share the same precision guide to capture roughness and macro profile, evaluating straightness, arc radius, angle, groove depth and pitch. Long-travel models (160–300 mm X, ±5 mm Z) suit shafts, rolls and mould surfaces.

  • λc: 0.8 mm for Ra 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm.
  • Force: 0.75 mN typical, below 0.4 mN for soft materials.
  • Direction: normally perpendicular to the machining lay.
04

Process animation

  1. Clean and level: wipe with lint-free cloth, align the part to the guide within 1°.
  2. Select cut-off: choose λc from the expected Ra, sampling length usually 5 × λc.
  3. Lower the stylus: automatic descent, zero after the force stabilises.
  4. Traverse: constant speed, acquire the profile.
  5. Filter and compute: Gaussian filter separates roughness, output Ra/Rz/Rq.
  6. Average: three positions per surface.
0102030405
05

Calculation & formulas

1. Ra: arithmetic mean deviation, Ra = (1/n)Σ|zi| for sampled points; samples of 2, 4, 3, 5, 1 µm give Ra = 3 µm.

2. Rz: mean of the five highest peaks and five deepest valleys per sampling length (maximum peak-to-valley under GB/T 3505).

3. Rmr: material ratio curve at height c, describing the bearing capability of mating faces.

4. Filtering: Gaussian λc = 0.8/2.5/8 mm separates roughness from waviness; λs suppresses noise.

5. Roundness: least-squares centre, minimum-zone, minimum circumscribed or maximum inscribed; spindle error should be under 1/5 of the tolerance.

06

規格

StandardTitleUse
GB/T 1031-2009Surface roughness — parameters and valuesParameter limits
GB/T 3505-2009Surface texture — profile termsTerminology
GB/T 10610-2009Rules and procedures for assessmentFiltering, evaluation
ISO 4287Profile method — termsExport projects
ISO 4288Rules and proceduresSampling length
07

選定ガイド

1. Separate three quantities: roughness (Ra/Rz/Rmr, micrometre-scale microtexture), waviness (W, 0.1–10 µm mid-spatial), and form error (roundness, cylindricity, macro geometry). They need different instruments or filters.

2. Profilometers and roundness testers are not interchangeable: profilometers measure Ra/Rz and profile along a line (XZ, CX series); roundness testers measure roundness, cylindricity and coaxiality of bodies of revolution (Y90 series). A cylinder bore needing both requires two machines or a combined type.

3. Sensor range sets capability: ±50 µm suffices for Ra alone; deep grooves, steps and large arcs need ±500 µm or more; mirror surfaces below Ra 0.01 µm need low-noise sensors and isolation.

4. Travel and load: XZ-150 for small parts, XZ-230/XZ-150G for mid-size bores and shafts, Y901200 or custom stages above one metre.

5. Software must support the standards: full Ra/Rz/Rq/Rsk/Rku/Rmr per GB/T 1031 and ISO 4287; roundness per GB/T 7234 with minimum-zone, least-squares, minimum-circumscribed and maximum-inscribed evaluation.

6. On-site use: workshops need vibration and dust control; portable units (DY-300) suit large parts at lower accuracy.

ModelTypeCapabilityTypical parts
XZ-150 / XZ-150GRoughness and profileRa/Rz + profileSmall precision parts
XZ-230Roughness and profileRa/Rz + long travelShafts, cylinder bores
CX-1(S) / CX-1(G)RoughnessRa/Rz/RmrShop-floor sampling
CX-3/100 / CX-3/160Roughness and profileRa + profile + stepsSpools, sealing faces
2207 / 2302ARoundnessRoundness/cylindricityBearing rings, journals
Y9025B/C/DRoundnessRoundness/coaxiality/wavinessPrecision spindles, bores
Y9060 / Y901200Large roundnessLarge-diameter roundnessWind bearings, flanges
DY-300PortableRa/RzLarge parts on site

Why results disagree: wrong cut-off wavelength, insufficient evaluation length, mismatched stylus radius and an unlevelled part account for most disputes.

08

試験方法

Preparation. Clean with ethanol to remove oil and chips; let the part stabilise to ambient (±2 °C); inspect the stylus at 20× for wear.

Settings. Choose λc to GB/T 1031 from expected Ra: 0.25 mm up to 0.1 µm, 0.8 mm for 0.1–2 µm, 2.5 mm for 2–10 µm, 8 mm above 10 µm; evaluation length 5 × λc.

Measurement. Stylus perpendicular to the lay, lower slowly, start when force is stable. Measure at least three positions per surface and average; on cylinders follow the generatrix.

Judgement. Compare with the drawing limit; no single reading should exceed 1.2 × the limit. Arbitrate with a profile instrument and a certified specimen.

Quality control. Daily check against Ra 0.4/1.6/6.3 specimens, recalibrate beyond 5% deviation, replace or verify the stylus every 12 months.

09

Industry applications

  • Hydraulics and pneumatics: Ra/Rz and Rmr on spools, cylinder bores and valve blocks, governing leakage and oil-film load capacity.
  • Bearings and spindles: raceway roundness, cylindricity and waviness, the latter being the main source of vibration and noise.
  • Engines and transmissions: bore roundness and cylindricity, crank-journal roundness, big-end bore form error.
  • Sealing faces: O-ring groove roughness and flange waviness affecting seal reliability.
  • Optics and semiconductors: Ra ≤0.005 µm, flatness and waviness requiring high-resolution sensors and isolation.
  • Moulds: cavity polish Ra and draft-face texture direction, affecting release and appearance.
  • Additive manufacturing: as-built Ra and support residue for post-processing validation.
  • Tools and coatings: edge honing radius and its correlation with coating roughness and adhesion.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0比較仕様比較