HVS-20 Vickers Hardness Tester

Vickers Hardness Tester

ModellHVS-20
  • 八档力(Kgf)2、3、5、8、10、12、15、20
  • 试验力加载自动(加卸/保持/卸载)
  • 符合标准(精度)GB/T4340.2国家标准、JJG151检定规程;
  • 测微目镜倍率10X (数显目镜)

By submitting you agree to our privacy policy.

01

Überblick

HVS-20触摸屏维氏硬度计为上海研润自主开发升级产品,采用5.6寸真彩色触摸屏、源于奥迪多媒体操控原理设计而成,操作更加直观方便是光机电一体化的第四代高新技术产品,该机器造型新颖,具有良好的可靠性,可操作性和直观性,是采用精密机械技术和光电技术的新型维氏和努普硬度测试仪器。
测量范围:微小、薄形、表面渗镀层试件和玻璃、陶瓷、玛瑙、人造宝石等较脆而又硬材料.是科研机构、企业及质检部门进行研究和检测的理想的硬度测试仪器
性能特点:
1、自动加卸荷试验力机构,试验力保持时间可在0~60秒间任意选择
2、采用计算机软件编程,可进行维氏和努氏标尺间的转化
3、稳定的光学测量系统,能调节测量光源的强弱
4、触摸屏面板显示屏直接显示硬度值,使用方便且测量精度高
5、实验结果和数据处理能够自动储存可通过微机打印机输出
技术参数:
产品型号
HVS-20M
八档力(Kgf)
2、3、5、8、10、12、15、20
试验力加载
自动(加卸/保持/卸载)
符合标准(精度)
GB/T4340.2国家标准、JJG151检定规程;
测微目镜倍率
10X (数显目镜)
试验力加载
自动(加卸/保持/卸载)
测微目镜移动方式
编码器采集
测量数据采集方式
自动采集
测量数据计算方式
自动计算
物镜倍率
10X(观察)、20X(测量)
10X(观察、测量)
总放大倍率
100X(观察)、200X(测量)
100X(观察、测量)
硬度值显示方式
触摸屏液晶显示
塔台控制方式
手动控制
转换标尺
HRA;HRB;HRC;HRD;HEF;HV;HK;
HBW;HR15N;HR30N;HR45N;HR15T;HR30T;HR45T
内置打印机
有(热敏纸微型打印机)
试验力读取
旋扭转换,自动读取
试验力保荷时间
0-60秒(s)(每1秒(s)为一单位)
光源亮度调节
5档可调节
试件最大高度
220 mm
压头中心到内壁距离
130 mm
外形尺寸
680(高)×216(宽)×565(深)mm
电源
AC220V/50Hz

HVS-20 Vickers Hardness Tester supplied by CHWES. 20 key specifications available on request.

02

Technische Daten

八档力(Kgf)2、3、5、8、10、12、15、20
试验力加载自动(加卸/保持/卸载)
符合标准(精度)GB/T4340.2国家标准、JJG151检定规程;
测微目镜倍率10X (数显目镜)
测微目镜移动方式编码器采集
测量数据采集方式自动采集
测量数据计算方式自动计算
物镜倍率10X(观察)、20X(测量) / 10X(观察、测量)
总放大倍率100X(观察)、200X(测量) / 100X(观察、测量)
硬度值显示方式触摸屏液晶显示
塔台控制方式手动控制
转换标尺HRA;HRB;HRC;HRD;HEF;HV;HK; HBW;HR15N;HR30N;HR45N;HR15T;HR30T;HR45T
内置打印机有(热敏纸微型打印机)
试验力读取旋扭转换,自动读取
试验力保荷时间0-60秒(s)(每1秒(s)为一单位)
光源亮度调节5档可调节
试件最大高度220 mm
压头中心到内壁距离130 mm
外形尺寸680(高)×216(宽)×565(深)mm
电源AC220V/50Hz

* Generated by rule engine over the product database; for pre-selection only.

03

Messprinzip

Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

  • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
  • Rockwell C 150 kgf: fast batch checking of hardened parts.
  • Brinell: castings, annealed and coarse-grain materials.
  • Leeb: portable rebound testing on large parts.
04

Process animation

  1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
  2. Mount and align: place the specimen, position the indenter over the test point.
  3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
  4. Load: apply force at the set rate, dwell 10–15 s.
  5. Measure: read diagonals or depth, compute HV/HRC.
  6. Gradient: step along depth and plot hardness versus distance.
0102030405
05

Calculation & formulas

1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

06

Normen

StandardTitleScope
GB/T 4340.1-2009Vickers hardness test — test methodVickers
GB/T 230.1-2018Rockwell hardness testRockwell
GB/T 231.1-2018Brinell hardness testBrinell
ISO 6507-1Vickers hardness testExport
ASTM E92Vickers hardness of metallic materialsAmericas
GB/T 17394.1-2014Leeb hardness testPortable

Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

07

Auswahl

1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

ModelPrincipleRangeTypical use
HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

08

Prüfverfahren

Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

09

Industry applications

  • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
  • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
  • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
  • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
  • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
  • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
  • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
  • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0VergleichTechnischer Vergleich