HOTHMAS-D5/10/30/50SZA Vickers Hardness Tester
Vickers Hardness Tester
- 测量分析系统HMAS‑硬度测量分析系统
- 光学成像系统维氏硬度大三通光学成像系统
HVS-1000Z · 2026-11-17 · +86 21 5748 2007
Micro Vickers Hardness Tester
By submitting you agree to our privacy policy.
HVS-1000Z自动转塔数显显微硬度计(大屏幕液晶屏显)是全新设计并推出的近期一代光机电一体化的高新技术产品,充分利用光机电一体化技术,一键式操作,高效快捷;采用C语言编程、双核双通道控制系统;液晶操作面板,编码器直接采集数据,可实现任意硬度单位双显示。配备大容量存储系统、微型打印机,更适合批量试样检测。
HVS-1000Z自动转塔数显显微硬度计适用范围:主要用于测量微小、薄型试件、脆硬件的测试,通过选用各种附件或者升级各种结构可广泛的用于各种金属(黑色金属、有色金属、铸件、合金材料等)、金属组织、金属表面加工层、电镀层、硬化层(氧化、各种渗层、涂镀层)、热处理试件、碳化试件、淬火试件、相夹杂点的微小部分,玻璃、玛瑙、人造宝石、陶瓷等脆硬非金属材料的测试,在细微部分进行精密定位的多点测量,压痕的深层测试与分析,渗镀层测试与分析,硬度梯度的测试,金相组织结构的观察与研究,涂镀层厚度的测量与分析等。是实验室质检部门、计量院所质量控制、材料研究的必备检测仪器。
突出特点:
1、配备数字式编码器直接采集数据,高精度测量。
2、高分辨率的成像系统,可高清晰的观察显示出压痕。
3、超大屏幕,显示清晰度高,可显示参数多样(压痕长度、硬度结果、光源亮度、塔台位置、加载时间等)中文操作系统,使用方便快捷;
4、物镜(压头)-塔台基板-光学系统-照明四者一体化结构设计,几乎做到了100%精美光学系统;
5、硬度测量进程同步性,可清晰直观的观察到机器测试进度。
6、自动转塔:压头与物镜自动切换,高精度的电机控制技术,让塔台转换更加轻松自如。
产品特点:
1、试验力小,对薄形样品或涂层均可测试;
2、压痕小,可认为无损检测,同时可在极小范围内进行多点测试;
3、全新浮点计算方法,使测试结果与理论结果更加接近一致;
4、主机硬件及软件采用预留端口设置,部分功能升级只需轻松拨码即可实现,使后续升级服务更加简便;
5、采用高端的图形图像处理技术与数据处理技术,图像压痕清晰,测试精度高;
6、高精度的电机控制技术,让塔台转换更加轻松自如;
7、可选择控制的塔台转动步数,让塔台定位更加正确;
8、可调的加卸载系统,让操作人员可轻松的完成多次测试;
9、可0-100%无级调节的照明系统,减轻了操作人员的视觉疲劳,同时自动控制的照明系统还可完成自动关闭与启动;
10、高级存储系统可以随时记忆测试结果,避免断电带来的数据丢失,高级时钟控制系统,让时间更加明了;
技术参数:
1、转塔方式:自动转塔
2、变荷装置构造:凸轮结构
3、升降丝杆:丝杆
4、试验力:(8级) N:0.098N、0.245N、0.490N、0.981N、1.961N、2.942N、4.903N、9.807N
(8级) gf: 10gf、25gf、50gf、100gf、200gf、300gf、500gf、1000gf
(8级) 标尺:HV0.01、HV0.025、HV0.05、HV0.1、HV0.2、HV0.3、HV0.5、HV1
5、试验力加载 :施加试验力速度:0.05mm/s,自动(加卸/保持/卸载)
6、符合标准(精度):GB/T4340 国标
7、X-Y移动平台 :试台尺寸:100X100mm,试台移动范围25X25mm,机械读数0.01mm
8、理论硬度测量范围 :0.001-9999HV
9、硬度值显示方式:数显液晶大屏幕120×80mm
10、目镜:10X(数显目镜)
11、物镜倍率:10X(观察)、40X(测量)
12、总放大倍数:100X(观察时)、400X(测量时)
13、最小检测单位:0.030μm
14、测微目镜移动方式 :欧姆龙编码器
15、测量数据采集方式 :自动采集
16、测量数据计算方式 :自动计算
17、换算标尺:布氏、洛氏、表面洛氏、肖氏、抗拉强度
18、试验力选择 :外置式选力旋钮(自动转换)
19、试验力保荷时间:0~99秒,最小变动量1秒
20、试件最大高度:85mm
21、压头中心到内壁距离 :110 mm
22、测试储存次数 :0~99次
23、试验力选择 :外置式选力旋钮(自动转换)
24、试验力保荷时间 : 0~99秒,最小变动量1秒
25、内置打印机 :微型打印机
26、光亮度调节 :0-100%可调,步进4%
27、机身工艺 :铸造机身(铝11-14mm)
28、外形尺寸 :460X230X490mm
29、电源:AC220V/50Hz
HVS-1000Z Micro Vickers Hardness Tester supplied by CHWES. 29 key specifications available on request.
| 转塔方式 | 自动转塔 |
|---|---|
| 变荷装置构造 | 凸轮结构 |
| 升降丝杆 | 丝杆 |
| 试验力 | (8级) N:0.098N、0.245N、0.490N、0.981N、1.961N、2.942N、4.903N、9.807N |
| (8级) gf | 10gf、25gf、50gf、100gf、200gf、300gf、500gf、1000gf |
| (8级) 标尺 | HV0.;HV0.0;HV0.;HV0.;HV0.;HV0.;HV0.;HV1 |
| 试验力加载 | 施加试验力速度:0.05mm/s,自动(加卸/保持/卸载) |
| 符合标准(精度) | GB/T4340 国标 |
| X-Y移动平台 | 试台尺寸:100X100mm,试台移动范围25X25mm,机械读数0.01mm |
| 理论硬度测量范围 | 0.001-9999HV |
| 硬度值显示方式 | 数显液晶大屏幕120×80mm |
| 目镜 | 10X(数显目镜) |
| 物镜倍率 | 10X(观察)、40X(测量) |
| 总放大倍数 | 100X(观察时)、400X(测量时) |
| 最小检测单位 | 0.030μm |
| 测微目镜移动方式 | 欧姆龙编码器 |
| 测量数据采集方式 | 自动采集 |
| 测量数据计算方式 | 自动计算 |
| 换算标尺 | 布氏、洛氏、表面洛氏、肖氏、抗拉强度 |
| 试验力选择 | 外置式选力旋钮(自动转换) |
| 试验力保荷时间 | 0~99秒,最小变动量1秒 |
| 试件最大高度 | 85mm |
| 压头中心到内壁距离 | 110 mm |
| 测试储存次数 | 0~99次 |
| 内置打印机 | 微型打印机 |
| 光亮度调节 | 0-100%可调,步进4% |
| 机身工艺 | 铸造机身(铝11-14mm) |
| 外形尺寸 | 460X230X490mm |
| 电源 | AC220V/50Hz |
* Generated by rule engine over the product database; for pre-selection only.
Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.
Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.
1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.
2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.
3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.
4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.
5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.
| Standard | Title | Scope |
|---|---|---|
| GB/T 4340.1-2009 | Vickers hardness test — test method | Vickers |
| GB/T 230.1-2018 | Rockwell hardness test | Rockwell |
| GB/T 231.1-2018 | Brinell hardness test | Brinell |
| ISO 6507-1 | Vickers hardness test | Export |
| ASTM E92 | Vickers hardness of metallic materials | Americas |
| GB/T 17394.1-2014 | Leeb hardness test | Portable |
Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.
1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.
2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.
3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.
4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.
5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.
6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.
| Model | Principle | Range | Typical use |
|---|---|---|---|
| HRC-150SMJ | Rockwell, motorised digital | HRA/HRB/HRC | Batch sampling in heat treatment |
| HRC-150SM / HRC-150M | Rockwell | HRA/HRB/HRC | Incoming and in-process checks |
| HRC-45M | Superficial Rockwell | 15N/30N/45N | Sheet, plating, case layers |
| HRS-150M / XHRS-150M | Digital Rockwell | HRA/HRB/HRC | Lines needing data upload |
| HBRVS-187.5 | Brinell-Vickers-Rockwell | HBW/HRA/HRB/HRC/HV | Mixed low-volume production |
Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.
Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.
Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.
Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.
Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.
Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.