HV-30 Vickers Hardness Tester

Vickers Hardness Tester

ModellHV-30
  • 转塔方式手动转塔
  • 加载机构砝码加载
  • 升降机构精密梯形丝杆
  • 硬度值显示方式LCD 屏

By submitting you agree to our privacy policy.

01

Überblick

HV-30小负荷维氏硬度计是第一代光机电一体化的高新技术产品,该机器造型新颖,具有良好的可靠性,可操作性和直观性,是采用精密机械技术和光电技术的新型维氏和努普硬度测试仪器.该机采用计算机软件编程,光学测量系统.通过软键输入,可选择维氏和努氏硬度的测量、能调节测量光源的强弱,能选择保荷时间,在数码管显示屏上能显示试验方法、试验力,通过面板输入测量压痕对角线长度、屏幕直接读出硬度值,简便了查表的繁琐,使用方便,测量精度高.该维氏硬度计优质的测量装换和测微目镜一次测量读数结构,使硬度测量更加正确和方便.该维氏硬度计可选配摄影装置,能对所测压痕和材料金相组织进行拍摄,并且进行数据处理和分析,大大提高了工作效率。
性能特点:
1、自动加卸荷试验力机构,试验力保持时间可在0~99秒间任意选择
2、采用计算机软件编程,可进行维氏和努氏标尺间的转化
3、稳定的光学测量系统,能调节测量光源的强弱
4、面板显示屏直接显示硬度值,使用方便且测量精度高
测量范围:微小、薄形、表面渗镀层试件和玻璃、陶瓷、玛瑙、人造宝石等较脆而又硬的材料.是科研机构、企业及质检部门进行研究和检测的理想的硬度测试仪器.
技术参数:
型号
HV-30
转塔方式
手动转塔
加载机构
砝码加载
升降机构
精密梯形丝杆
硬度值显示方式
LCD 屏
HV‑30试验力
(30Kg):1kgf、3kgf、5kgf、10kgf、20kgf、30kgf;
转换标尺
HV、HK、HBW、HRA、HRB、HRC、HRD、HRF、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T
试验力加载
全自动(加载 / 保荷 / 卸载)
执行国家标准
GB/T4340 国家标准,ISO6507 质量认证,ASTM 标准
理论硬度测量范围
8 - 3000HV
目镜倍率
10X(机械目镜)
HV‑30物镜倍率
(30Kg、50Kg):10X(观察、测量)
HV‑30总放大倍数
(30Kg、50Kg):100X(观察、测量)
读数方式
鼓轮读数
计算方式
自动计算
最小检测单位
1μm
试验力保荷时间
0 - 99 秒,最小变动量 1 秒
试件最大高度
245mm
压头中心到内壁距离
138mm
电源电压
AC 220V/50Hz
外形尺寸
570*250*680mm(长*宽*高)
净重
46.0kg
毛重
61.0kg

HV-30 Vickers Hardness Tester supplied by CHWES. 22 key specifications available on request.

02

Technische Daten

转塔方式手动转塔
加载机构砝码加载
升降机构精密梯形丝杆
硬度值显示方式LCD 屏
HV‑30试验力(30Kg):1kgf、3kgf、5kgf、10kgf、20kgf、30kgf;
转换标尺HV、HK、HBW、HRA、HRB、HRC、HRD、HRF、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T
试验力加载全自动(加载 / 保荷 / 卸载)
执行国家标准GB/T4340 国家标准,ISO6507 质量认证,ASTM 标准
理论硬度测量范围8 - 3000HV
目镜倍率10X(机械目镜)
HV‑30物镜倍率(30Kg、50Kg):10X(观察、测量)
HV‑30总放大倍数(30Kg、50Kg):100X(观察、测量)
读数方式鼓轮读数
计算方式自动计算
最小检测单位1μm
试验力保荷时间0 - 99 秒,最小变动量 1 秒
试件最大高度245mm
压头中心到内壁距离138mm
电源电压AC 220V/50Hz
外形尺寸570*250*680mm(长*宽*高)
净重46.0kg
毛重61.0kg

* Generated by rule engine over the product database; for pre-selection only.

03

Messprinzip

Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

  • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
  • Rockwell C 150 kgf: fast batch checking of hardened parts.
  • Brinell: castings, annealed and coarse-grain materials.
  • Leeb: portable rebound testing on large parts.
04

Process animation

  1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
  2. Mount and align: place the specimen, position the indenter over the test point.
  3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
  4. Load: apply force at the set rate, dwell 10–15 s.
  5. Measure: read diagonals or depth, compute HV/HRC.
  6. Gradient: step along depth and plot hardness versus distance.
0102030405
05

Calculation & formulas

1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

06

Normen

StandardTitleScope
GB/T 4340.1-2009Vickers hardness test — test methodVickers
GB/T 230.1-2018Rockwell hardness testRockwell
GB/T 231.1-2018Brinell hardness testBrinell
ISO 6507-1Vickers hardness testExport
ASTM E92Vickers hardness of metallic materialsAmericas
GB/T 17394.1-2014Leeb hardness testPortable

Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

07

Auswahl

1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

ModelPrincipleRangeTypical use
HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

08

Prüfverfahren

Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

09

Industry applications

  • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
  • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
  • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
  • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
  • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
  • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
  • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
  • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0VergleichTechnischer Vergleich