HMAS-D3000HB Brinell Hardness Tester

Brinell Hardness Tester

ModellHMAS-D3000HB
  • 加载力方式电机(传感器加载)
  • 硬度测量系统HMAS 布氏硬度测量分析系统
  • 成像系统布氏硬度光学成像系统
  • 测量标尺HBW2.5/62.5、HBW2.5/187.5、HBW5/62.5、HBW5/125、HBW5/250、HBW5/750、HBW10/100、HBW10/250、HBW10/500、HBW10/1000、HBW10/1500、HBW10/3000

By submitting you agree to our privacy policy.

01

Überblick

HMAS-D3000HB布氏硬度测量分析系统主要用于铸铁、钢材、有色金属及软合金等材料的硬度测定,布氏硬度试验是所有硬度试验中压痕最大的一种试验法,它能反映出材料的综合性能,不受试样组织显微偏析及成分不均匀的影响,所以它是一种精度较高的硬度试验法。在冶金、锻造、未经淬火钢及有色金属等工业领域、实验室、大专院校和科研单位内广泛使用。
系统特点:
1、布氏硬度测量分析系统:自动高速测量。操作方便、功能强大,能够实时显示硬度压痕图像,采用了自主开发的数码调焦技术使看到的图像更加清晰,解决了传统需要通过硬度计目镜进行观察的不便之处;具有自动跟踪压痕图像、自动检测计算压痕大小,实时显示硬度计算结果;能够对压痕图像进行无级的放大缩小测量,对压痕图像很小的薄膜类材料也能精确测量;同时(HMAS软件系统)具有硬度测量结果统计评价分析,硬度SPC 分析,自动生成硬度分布曲线,自动生成PDF、Word、Excel等格式的硬度测量分析报告,图像保存,打印等功能。
2、CPU双核闭环控制系统;
3、自动采集目镜装置,自动计算硬度结果,高精密数字信号输出,确保力值精确性、示值稳定性;
4、自动转换标尺 可同时转换成洛氏、表面洛氏、维氏等硬度值。
5、本机配备微型打印机,可打印出硬度测试结果。
技术参数:
型号
HMAS‑D3000HB
加载力方式
电机(传感器加载)
硬度测量系统
HMAS 布氏硬度测量分析系统
成像系统
布氏硬度光学成像系统
测量标尺
HBW2.5/62.5、HBW2.5/187.5、HBW5/62.5、HBW5/125、HBW5/250、HBW5/750、HBW10/100、HBW10/250、HBW10/500、HBW10/1000、HBW10/1500、HBW10/3000
试验力级数
62.5kgf
(612.5N)、100kgf(980N)、125kgf(1225N)、187.5kgf(1837.5N)、250kgf(2450N)、500kgf(4900N)、750kgf(7350N)、1000kgf(9800N)、1500kgf(14700N)、3000Kgf(29400N)
转换标尺
HRC、HV、HK、HBW、HRA、HRD、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T、HRB、HRF
试验力加载
自动(加载/保荷/卸载)
执行国家标准
GB/T231.1 国家标准,GB/T231.2 国家标准,JJG150 检定规程
工业相机
130W
数据采集方式
电脑软件测量分析
理论硬度测量范围
8‑650HBW
硬度值显示方式
电脑显示
试验力保荷时间
0‑60 秒,最小变动量 1 秒
试件最大高度
230mm
压头中心到内壁距离
155mm
测试记录
0‑30 组
电源电压
AC 220V/50Hz
外形尺寸
512*223*745mm(长 * 宽 * 高)
净重
116.5kg
毛重
148.0kg

HMAS-D3000HB Brinell Hardness Tester supplied by CHWES. 20 key specifications available on request.

02

Technische Daten

加载力方式电机(传感器加载)
硬度测量系统HMAS 布氏硬度测量分析系统
成像系统布氏硬度光学成像系统
测量标尺HBW2.5/62.5、HBW2.5/187.5、HBW5/62.5、HBW5/125、HBW5/250、HBW5/750、HBW10/100、HBW10/250、HBW10/500、HBW10/1000、HBW10/1500、HBW10/3000
试验力级数62.5kgf (612.5N)、100kgf(980N)、125kgf(1225N)、187.5kgf(1837.5N)、250kgf(2450N)、500kgf(4900N)、750kgf(7350N)、1000kgf(9800N)、1500kgf(14700N)、3000Kgf(29400N)
转换标尺HRC、HV、HK、HBW、HRA、HRD、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T、HRB、HRF
试验力加载自动(加载/保荷/卸载)
执行国家标准GB/T231.1 国家标准,GB/T231.2 国家标准,JJG150 检定规程
工业相机130W
数据采集方式电脑软件测量分析
理论硬度测量范围8‑650HBW
硬度值显示方式电脑显示
试验力保荷时间0‑60 秒,最小变动量 1 秒
试件最大高度230mm
压头中心到内壁距离155mm
测试记录0‑30 组
电源电压AC 220V/50Hz
外形尺寸512*223*745mm(长 * 宽 * 高)
净重116.5kg
毛重148.0kg

* Generated by rule engine over the product database; for pre-selection only.

03

Messprinzip

Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

  • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
  • Rockwell C 150 kgf: fast batch checking of hardened parts.
  • Brinell: castings, annealed and coarse-grain materials.
  • Leeb: portable rebound testing on large parts.
04

Process animation

  1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
  2. Mount and align: place the specimen, position the indenter over the test point.
  3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
  4. Load: apply force at the set rate, dwell 10–15 s.
  5. Measure: read diagonals or depth, compute HV/HRC.
  6. Gradient: step along depth and plot hardness versus distance.
0102030405
05

Calculation & formulas

1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

06

Normen

StandardTitleScope
GB/T 4340.1-2009Vickers hardness test — test methodVickers
GB/T 230.1-2018Rockwell hardness testRockwell
GB/T 231.1-2018Brinell hardness testBrinell
ISO 6507-1Vickers hardness testExport
ASTM E92Vickers hardness of metallic materialsAmericas
GB/T 17394.1-2014Leeb hardness testPortable

Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

07

Auswahl

1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

ModelPrincipleRangeTypical use
HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

08

Prüfverfahren

Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

09

Industry applications

  • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
  • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
  • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
  • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
  • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
  • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
  • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
  • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0VergleichTechnischer Vergleich