HOTHMAS-D5/10/30/50SZA Vickers Hardness Tester
Vickers Hardness Tester
- 测量分析系统HMAS‑硬度测量分析系统
- 光学成像系统维氏硬度大三通光学成像系统
HMAS-C5SZA · 2026-11-17 · +86 21 5748 2007
Vickers Hardness Tester
By submitting you agree to our privacy policy.
HMAS-C5/10/20/30/50SZA维氏硬度测量系统是研润公司新推出的一款高性能硬度测量系统。本机是在传统型的显微硬度测量功能上新开发的新一代硬度计.该机具有良好的可靠性,可操作性和直观性,是采用精密机械技术、光电技术、和材料硬度测量软件是新型维氏硬度测试仪器。
本机配备了自动运动控制系统:X-Y自动工作平台,可设定位置、距离、平台自动移动,可在行程范围内自由运动的控制方式,不仅仅实现了操作的便利性,同时也为精密尺寸测量(如涂镀层厚度、金相分析及硬度梯等)及金属结构组织分析提供了更正确的分析手段。
HMAS-C5/10/20/30/50SZA维氏硬度测量系统适用于测定微小、薄形试件、表面渗镀层等试件的显微硬度和测定玻璃、陶瓷、玛瑙、宝石等脆性材料的维氏硬度,是科研机构、工厂及质监部门进行材料研究和检测的理想硬度测试仪器。
性能特点:
1、仪器配备高精密的CCD图像成像系统,将仪器内部采集压痕图像转换进入电脑软件中心。
2、本仪器通过电脑控制机器系统,可以在计算机上通过鼠标很方便的完成对硬度计的实时控制,可以实现所有硬度计的相关功能,效果与直接硬度计面板一样。
3、本机配备了自动运动控制系统:X-Y自动工作台,可在行程范围内自由运动的控制方式,不仅仅实现了操作的便利性,同时也为精密尺寸测量(如涂镀层厚度、金相分析及硬度梯度等)及金属结构组织分析提供了更正确的分析手段.
⑴程序控制电动X-Y工作台:移动范围:50×50mm
⑵控制:用测试软件控制
⑶单点压痕或自动连续多点压痕
⑷变速移动:平台移动时,速度可设置
⑸鼠标点动功能:鼠标点哪平台移动到哪
技术参数:
产品型号
HMAS-C5SZA
HMAS-C10SZA
HMAS-C20SZA
HMAS-C30SZA
HMAS-C50SZA
测量分析系统
HMAS-D测量分析系统
转塔方式
自动转塔
六档力(Kgf)
0.2、0.3、0.5、1、3、5
0.3、0.5、1、3、5、10
/
1、3、5、10、20、30
1、5、10、20、30、50
选配:八档力(Kgf)
0.2、0.3、0.5、1、2、3、4、5
0.3、0.5、1、 2、3、 4、5、10
2、3、5、8、10、12、15、20
2、5、8、10、12、15、 20、30
2、5、8、10、15、20、30、50
试验力加载
自动(加卸/保持/卸载)
符合标准(精度)
GB/T4340.2国家标准、JJG151检定规程;
测微目镜倍率
10X (数显目镜)
试验力加载
自动(加卸/保持/卸载)
测微目镜移动方式
数字编码器采集
测量数据采集方式
主机按键采集 ,电脑软件测量
测量数据计算方式
主机自动计算分析,电脑软件测量分析
X-Y自动平台
尺寸:150 × 150 ×60 mm
移动范围:50 ×50 mm
控制:用测试软件控制
单点压痕或自动连续多点压痕测试
变速移动:平台移动速度可调
物镜倍率
10X(观察)、20X(测量)
10X(观察、测量)
总放大倍率
100X(观察)、200X(测量)
100X(观察、测量)
电脑放大
约800倍
约400倍
转换标尺
HRA;HRB;HRC;HRD;HEF;HV;HK;HBW;HR15N;HR30N;HR45N;HR15T;HR30T;HR45T
内置打印机
主机内置微型打印机、电脑打印输出
试验力读取
旋扭转换,自动读取
试验力保荷时间
0-60秒(s)(每1秒(s)为一单位)
光源亮度调节
5档可调节
试件最大高度
170 mm
压头中心到内壁距离
130 mm
外形尺寸
680(高)×216(宽)×565(深)mm
电源
AC220V/50Hz
HMAS-C5SZA Vickers Hardness Tester supplied by CHWES. 3 key specifications available on request.
| 测量分析系统 | HMAS-D测量分析系统 |
|---|---|
| 转塔方式 | 自动转塔 |
| 六档力(Kgf) | 0.2、0.3、0.5、1、3、5 / 0.3、0.5、1、3、5、10 / / / 1、3、5、10、20、30 / 1、5、10、20、30、50 |
* Generated by rule engine over the product database; for pre-selection only.
Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.
Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.
1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.
2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.
3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.
4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.
5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.
| Standard | Title | Scope |
|---|---|---|
| GB/T 4340.1-2009 | Vickers hardness test — test method | Vickers |
| GB/T 230.1-2018 | Rockwell hardness test | Rockwell |
| GB/T 231.1-2018 | Brinell hardness test | Brinell |
| ISO 6507-1 | Vickers hardness test | Export |
| ASTM E92 | Vickers hardness of metallic materials | Americas |
| GB/T 17394.1-2014 | Leeb hardness test | Portable |
Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.
1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.
2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.
3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.
4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.
5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.
6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.
| Model | Principle | Range | Typical use |
|---|---|---|---|
| HRC-150SMJ | Rockwell, motorised digital | HRA/HRB/HRC | Batch sampling in heat treatment |
| HRC-150SM / HRC-150M | Rockwell | HRA/HRB/HRC | Incoming and in-process checks |
| HRC-45M | Superficial Rockwell | 15N/30N/45N | Sheet, plating, case layers |
| HRS-150M / XHRS-150M | Digital Rockwell | HRA/HRB/HRC | Lines needing data upload |
| HBRVS-187.5 | Brinell-Vickers-Rockwell | HBW/HRA/HRB/HRC/HV | Mixed low-volume production |
Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.
Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.
Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.
Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.
Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.
Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.