HBS-62.5MZ Brinell Hardness Tester

Brinell Hardness Tester

ModellHBS-62.5MZ
  • 转塔方式自动转塔
  • 变荷装置机构传感器闭环控制
  • 升降机构精密梯形丝杆
  • 试验力1、2.5、5、6.25、10、15.625、25、30、31.25、62.5KG

By submitting you agree to our privacy policy.

01

Überblick

HBS-62.5M/MZ系列触摸屏数显小负荷布氏硬度计是光机电一体化的高新技术产品,具有良好的可靠性,可操作性,是小负荷部氏硬度计的前沿科技新产品。该机采用高精度力传感器闭环控制系统,电机施加压力无需砝码、试验力的加荷、保荷、卸荷采用自动切换,操作简便迅速。试验力更广、更正确;高倍率光学系统,压痕更清晰,便于测量,硬度测量更精确。
触摸式操作直观显示测试内容。通过触摸点击选择测试方法,一键式启动硬度测试无需提前人工施加初实验力、实验力值实时显示更加直观、确保力值的真实性。精确到克的实时力值显示是本机的优势之一。在大屏幕屏上实时显示试验方法、试验力,硬度值、试验力保持时间等。此设备提供了硬度测试数据自动储存,自动判断最大值、最小值、极差值、平均值。
布氏硬度试验主要用于铸铁、钢材、有色金属及软合金等材料的硬度测定,此外还可以用于硬质的塑料、电木等某些非金属材料硬度的测定。适用于工厂、车间、试验室、大专院校和科研机构。
结构特点:
全新的机身:
采用柔线型铸铝机身,使得机器整体美观轻便;
新的塔台机构:
在塔台上一次最多可以安装三个物镜,使得它更像一台显微镜,这样您就能够观察多种样品表面条件。(需要定制)
照明机构:
超长的灯源使用寿命。
全新大三通结构:
全新大三通光路系统,接近100%光吸收。
塔台切换机构:
塔台精确90度等分,弹性定位结构。使每次切换可准确定位于卡槽内。
先进的浮点计算方法:
全新浮点计算方法,使测试结果与理论结果更加接近一致。
可以扩展的自动功能:
选装自动载物台(特殊机型需定制)、选装计算机,硬度测量软件等多种配件,硬度计可以升级成多种不同程度的自动控制系统。
产品特点:
1、传感器闭环控制开机即用,电动加载,无需安装砝码调试;
2、本机布氏标尺10种试验标尺;
3、触摸屏控制系统、操作方便快捷;
4、硬度值自动储存,自动计算平均值、最大值、最小值、极差值;
5、力值实时显示;
技术参数:
型号
HBS‑62.5MZ
转塔方式
自动转塔
变荷装置机构
传感器闭环控制
升降机构
精密梯形丝杆
试验力
1、2.5、5、6.25、10、15.625、25、30、31.25、62.5KG
测量标尺
HBW1/1、HBW1/2.5、HBW1/5、HBW1/10、HBW1/30、HBW2.5/6.25、HBW2.5/15.625、HBW2.5/31.25、HBW2.5/62.5、HBW5/25、HBW5/62.5
换算标尺
14 种硬度标尺
试验力加载
自动(加载/保荷/卸载)
试验力选择方式
触摸屏
执行国家标准
GB/T4340 国家标准,ISO6507 质量认证,ASTM 标准
理论硬度测量范围
4‑650HBW
光亮度调节
1‑10 级可调,步进 1 级
硬度值显示方式
触摸屏
目镜
10X(数显目镜)
物镜倍率
5X(10X 选配)
总放大倍数
50X
读数方式
数显目镜按钮采集
计算方式
自动计算
最小检测单位
2μm
测微目镜移动方式
手动
测量数据采集方式
按键
测量结果计算方式
自动计算
试验力保荷时间
0‑60 秒,最小变动量 1 秒
试件最大高度
245mm
压头中心到内壁距离
138mm
电源电压
AC 220V/50Hz
机身厚度
8‑10mm
外形尺寸
570*220*680mm(长*宽*高)
净重
40.0kg
毛重
55.0kg

HBS-62.5MZ Brinell Hardness Tester supplied by CHWES. 29 key specifications available on request.

02

Technische Daten

转塔方式自动转塔
变荷装置机构传感器闭环控制
升降机构精密梯形丝杆
试验力1、2.5、5、6.25、10、15.625、25、30、31.25、62.5KG
测量标尺HBW1/1、HBW1/2.5、HBW1/5、HBW1/10、HBW1/30、HBW2.5/6.25、HBW2.5/15.625、HBW2.5/31.25、HBW2.5/62.5、HBW5/25、HBW5/62.5
换算标尺14 种硬度标尺
试验力加载自动(加载/保荷/卸载)
试验力选择方式触摸屏
执行国家标准GB/T4340 国家标准,ISO6507 质量认证,ASTM 标准
理论硬度测量范围4‑650HBW
光亮度调节1‑10 级可调,步进 1 级
硬度值显示方式触摸屏
目镜10X(数显目镜)
物镜倍率5X(10X 选配)
总放大倍数50X
读数方式数显目镜按钮采集
计算方式自动计算
最小检测单位2μm
测微目镜移动方式手动
测量数据采集方式按键
测量结果计算方式自动计算
试验力保荷时间0‑60 秒,最小变动量 1 秒
试件最大高度245mm
压头中心到内壁距离138mm
电源电压AC 220V/50Hz
机身厚度8‑10mm
外形尺寸570*220*680mm(长*宽*高)
净重40.0kg
毛重55.0kg

* Generated by rule engine over the product database; for pre-selection only.

03

Messprinzip

Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

  • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
  • Rockwell C 150 kgf: fast batch checking of hardened parts.
  • Brinell: castings, annealed and coarse-grain materials.
  • Leeb: portable rebound testing on large parts.
04

Process animation

  1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
  2. Mount and align: place the specimen, position the indenter over the test point.
  3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
  4. Load: apply force at the set rate, dwell 10–15 s.
  5. Measure: read diagonals or depth, compute HV/HRC.
  6. Gradient: step along depth and plot hardness versus distance.
0102030405
05

Calculation & formulas

1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

06

Normen

StandardTitleScope
GB/T 4340.1-2009Vickers hardness test — test methodVickers
GB/T 230.1-2018Rockwell hardness testRockwell
GB/T 231.1-2018Brinell hardness testBrinell
ISO 6507-1Vickers hardness testExport
ASTM E92Vickers hardness of metallic materialsAmericas
GB/T 17394.1-2014Leeb hardness testPortable

Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

07

Auswahl

1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

ModelPrincipleRangeTypical use
HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

08

Prüfverfahren

Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

09

Industry applications

  • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
  • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
  • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
  • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
  • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
  • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
  • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
  • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0VergleichTechnischer Vergleich