HBRVS-187.5MV Hardness Tester

Hardness Tester

ModellHBRVS-187.5MV
  • 型号HBRVS-187.5MV
  • 操作方式触摸屏
  • 洛氏硬度标尺HRA、HRB、HRC、HRD、HRE、HRF、HRG、HRH、HRK、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T
  • 布氏硬度标尺HBW2.5/15.6;HBW2.5/31.;HBW2.5/62.;HBW5/1;HBW2.5/187.5

By submitting you agree to our privacy policy.

01

Überblick

HBRVS-187.5MV智能数显布洛维硬度计为研润自主研发生产第五代高端产品,采用7寸高清彩色触摸屏控制。该机采用C++语言编程,触摸式操作,与闭环式高精度传感器的融合,大大提高了工作效率及力值的准确性,是光、机、电一体化的高新技术产品。本布洛维硬度计可进行布氏、洛氏、维氏三种试验方法测试,具备了二十一级试验力的多功能硬度计,能满足多种硬度测试需求。试验力的加荷、保荷、卸荷采用自动切换,操作简便迅速。
触摸式操作直观显示测试内容。通过触摸点击选择测试方法,一键式启动硬度测试无需提前人工施加初实验力、实验力值实时显示更加直观、确保力值的真实性。力值精确到克且实时显示方便您观察力值的实时变化。洛氏硬度值自动计算精确到小数点后一位,并提供棒材硬度测试标准避免了硬度结果查表的繁琐。在大屏幕屏上实时显示试验方法、试验力,硬度值、试验力保持时间等。此设备提供了硬度测试数据自动储存,自动判断最大值、最小值、极差值、平均值。
性能特点:
7寸高清彩色触摸屏,触摸式操作系统。
闭环传感器控制系统,无需砝码。
无需特殊安装,甚至无需售后。
无需施加初始试验力,自动加卸试验力。
测量精度高,洛氏硬度值自动修正。
测试过程中力值实时显示且精确到克。
硬度值自动储存,自动计算平均值、最大值、最小值、极差值。
硬度标尺选择时,提示选用压头。
布氏、洛氏、维氏硬度的三种试验方法测试。
布洛维硬度计的技术参数:
型号: HBRVS-187.5MV
操作方式: 触摸屏
洛氏硬度标尺:
HRA、HRB、HRC、HRD、HRE、HRF、HRG、HRH、HRK、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T;
布氏硬度标尺: HBW2.5/15.625、HBW2.5/31.25、HBW2.5/62.5、HBW5/125、HBW2.5/187.5;
维氏硬度标尺: HV5、HV10、HV20、HV30、HV50、HV100
洛氏试验力: 60Kg、100Kg、150Kg、15 Kg、30 Kg、45 Kg;
布氏试验力: 15.625 Kg、31.25Kg、62.5Kg、125 Kg、187.5Kg;
维氏试验力: 5 Kg、10 Kg、20 Kg、30Kg、50 Kg、100Kg
洛氏硬度测试范围: HRA:20~88、HRB:20~100、HRC:20~70;
布氏硬度测试范围: HBW:8HBW~650HBW;
维氏硬度测试范围: 20HV~3000HV;
执行国家标准: GB/T230.1 国家标准,GB/T 230.2 国家标准,GB/T231.1 国家标准,GB/T231.2
国家标准,GB/T4340.1 国家标准,GB/T3440.2 国家标准,JJG112 检定规程
试验力保荷时间: 机器设定 0-99 秒,最小变动量 1 秒
计算方式: 自动计算
物镜倍率: 2.5X、5X、10X
压头中心距离: 160mm
测试洛氏硬度试件最大高度: 175mm
测试布氏、维氏硬度试件最大高度: 125mm
数据输出: U 盘输出
电源电压: AC 220V/50Hz
外形尺寸:606*350*750mm(长*宽*高)
净重: 88.0kg
毛重: 105.0kg
布洛维硬度计附件:
1、金刚石洛氏压头:1只;
2、金刚石维氏压头:1只;
3、φ1.5875mm、φ2.5mm、φ5mm球压头:各1只;
4、大平试台:1只;
5、中平试台:1只;
6、“V”型试台:1只;
7、标准洛氏硬度块:;
HRC 高、低:各1块;
HRB:1块;
8、标准维氏硬度块:1块;
9、标准布氏硬度块:1块;
10、溜板试台:1套;
11、电源线:1根;
12、保险丝2A:1只;
13、防尘塑料罩:1套;
14、产品使用说明书:1本;
15、产品合格保修卡:1套;
16、显微镜座:1只;
17、测微目镜(15X):1只;
18、2.5X物镜:1只;
19、5X物镜:1只;
20、10X物镜:1只;
21、外照明灯:1只;
22、内照明灯:1只;

HBRVS-187.5MV Hardness Tester supplied by CHWES. 25 key specifications available on request.

02

Technische Daten

型号HBRVS-187.5MV
操作方式触摸屏
洛氏硬度标尺HRA、HRB、HRC、HRD、HRE、HRF、HRG、HRH、HRK、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T
布氏硬度标尺HBW2.5/15.6;HBW2.5/31.;HBW2.5/62.;HBW5/1;HBW2.5/187.5
维氏硬度标尺HV;HV;HV;HV;HV;HV100
洛氏试验力60Kg、100Kg、150Kg、15 Kg、30 Kg、45 Kg
布氏试验力15.625 Kg、31.25Kg、62.5Kg、125 Kg、187.5Kg
维氏试验力5 Kg、10 Kg、20 Kg、30Kg、50 Kg、100Kg
洛氏硬度测试范围HRA:20~
HRB20~1
HRC20~70
布氏硬度测试范围HBW:8HBW~650HBW
维氏硬度测试范围20HV~3000HV
执行国家标准GB/T230.1 国家标准,GB/T 230.2 国家标准,GB/T231.1 国家标准,GB/T231.2;国家标准,GB/T4340.1 国家标准,GB/T3440.2 国家标准,JJG112 检定规程
试验力保荷时间机器设定 0-99 秒,最小变动量 1 秒
计算方式自动计算
物镜倍率2.5X、5X、10X
压头中心距离160mm
测试洛氏硬度试件最大高度175mm
测试布氏、维氏硬度试件最大高度125mm
数据输出U 盘输出
电源电压AC 220V/50Hz
外形尺寸606*350*750mm(长*宽*高)
净重88.0kg
毛重105.0kg;布洛维硬度计

* Generated by rule engine over the product database; for pre-selection only.

03

Messprinzip

Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

  • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
  • Rockwell C 150 kgf: fast batch checking of hardened parts.
  • Brinell: castings, annealed and coarse-grain materials.
  • Leeb: portable rebound testing on large parts.
04

Process animation

  1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
  2. Mount and align: place the specimen, position the indenter over the test point.
  3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
  4. Load: apply force at the set rate, dwell 10–15 s.
  5. Measure: read diagonals or depth, compute HV/HRC.
  6. Gradient: step along depth and plot hardness versus distance.
0102030405
05

Calculation & formulas

1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

06

Normen

StandardTitleScope
GB/T 4340.1-2009Vickers hardness test — test methodVickers
GB/T 230.1-2018Rockwell hardness testRockwell
GB/T 231.1-2018Brinell hardness testBrinell
ISO 6507-1Vickers hardness testExport
ASTM E92Vickers hardness of metallic materialsAmericas
GB/T 17394.1-2014Leeb hardness testPortable

Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

07

Auswahl

1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

ModelPrincipleRangeTypical use
HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

08

Prüfverfahren

Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

09

Industry applications

  • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
  • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
  • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
  • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
  • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
  • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
  • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
  • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0VergleichTechnischer Vergleich