HOTHMAS-D5/10/30/50SZA Vickers Hardness Tester
Vickers Hardness Tester
- 测量分析系统HMAS‑硬度测量分析系统
- 光学成像系统维氏硬度大三通光学成像系统
HBM-2017A · 2026-11-17 · +86 21 5748 2007
Brinell Hardness Tester
By submitting you agree to our privacy policy.
MC010-HBM-2017A数显异形布氏硬度计主要用于铸铁、钢材、有色金属及软合金等材料的异形零件硬度测定,布氏硬度试验是所有硬度试验中压痕最大的一种试验法,它能反映出材料的综合性能,不受试样组织显微偏析及成分不均匀的影响,所以它是一种精度较高的硬度试验法。在冶金、锻造、未经淬火钢及有色金属等工业领域、实验室、大专院校和科研单位内广泛使用。
产品特点:
1、本布氏硬度计不需要传统的砝码加载实验力,采用全电子闭环式传感器加载控制系统,高精度、高重复性和稳定性好、操作简便。
2、人性化操作界面,让使用者更方便、直观、操作更简便。
3、本布氏硬度计是针对异形零件设计而成,对异形零件的硬度测定有着非常方便和正确的测定。
4、本布氏硬度计可以定制成流水线非标布氏硬度计,可以根据使用的工作量制作成自动电脑型布氏硬度计。
5、本布氏硬度计可以加载门式试验系统,制作成超高精度的自动化流水线布氏硬度测量系统。
技术参数:
产品型号
HBM-2017A
操作方式
数显布氏
布氏标尺
HBW2.5/62.5、HBW10/100、HBW5/125、HBW2.5/187.5、HBW10/250、
HBW10/500、HBW5/750、HBW10/1000、HBW10/1500、HBW10/3000
试验力加载
自动(加卸/保持/卸载)
符合标准(精度)
GB/T231.2国家标准、JJG150检定规程
测微目镜
读数显微镜20X、可选配加装自动系统
最小检测单位
0.0005mm
测量数据采集方式
自动采集
测量数据计算方式
自动
硬度值显示方式
触摸屏数显
压头规格
直径2.5mm, 5mm, 10mm
转换标尺
布洛维三种
内置打印机
微型打印机
测试储存组数
30组
硬度测量范围
8-650HBW
试验力保荷时间
0-99秒(s)(每1秒(s)为一单位)
光源亮度调节
10级
试件最大高度
定制
压头中心到内壁距离
定制
大平台直径
定制
中平台直径
定制
V型台尺寸
定制
外形尺寸
850x500x800mm
重量
235Kg
电源
AC220V/50Hz
HBM-2017A Brinell Hardness Tester supplied by CHWES. 24 key specifications available on request.
| 操作方式 | 数显布氏 |
|---|---|
| 布氏标尺 | HBW2.5/62.5、HBW10/100、HBW5/125、HBW2.5/187.5、HBW10/250、 HBW10/500、HBW5/750、HBW10/1000、HBW10/1500、HBW10/3000 |
| 试验力加载 | 自动(加卸/保持/卸载) |
| 符合标准(精度) | GB/T231.2国家标准、JJG150检定规程 |
| 测微目镜 | 读数显微镜20X、可选配加装自动系统 |
| 最小检测单位 | 0.0005mm |
| 测量数据采集方式 | 自动采集 |
| 测量数据计算方式 | 自动 |
| 硬度值显示方式 | 触摸屏数显 |
| 压头规格 | 直径2.5mm, 5mm, 10mm |
| 转换标尺 | 布洛维三种 |
| 内置打印机 | 微型打印机 |
| 测试储存组数 | 30组 |
| 硬度测量范围 | 8-650HBW |
| 试验力保荷时间 | 0-99秒(s)(每1秒(s)为一单位) |
| 光源亮度调节 | 10级 |
| 试件最大高度 | 定制 |
| 压头中心到内壁距离 | 定制 |
| 大平台直径 | 定制 |
| 中平台直径 | 定制 |
| V型台尺寸 | 定制 |
| 外形尺寸 | 850x500x800mm |
| 重量 | 235Kg |
| 电源 | AC220V/50Hz |
* Generated by rule engine over the product database; for pre-selection only.
Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.
Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.
1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.
2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.
3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.
4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.
5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.
| Standard | Title | Scope |
|---|---|---|
| GB/T 4340.1-2009 | Vickers hardness test — test method | Vickers |
| GB/T 230.1-2018 | Rockwell hardness test | Rockwell |
| GB/T 231.1-2018 | Brinell hardness test | Brinell |
| ISO 6507-1 | Vickers hardness test | Export |
| ASTM E92 | Vickers hardness of metallic materials | Americas |
| GB/T 17394.1-2014 | Leeb hardness test | Portable |
Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.
1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.
2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.
3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.
4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.
5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.
6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.
| Model | Principle | Range | Typical use |
|---|---|---|---|
| HRC-150SMJ | Rockwell, motorised digital | HRA/HRB/HRC | Batch sampling in heat treatment |
| HRC-150SM / HRC-150M | Rockwell | HRA/HRB/HRC | Incoming and in-process checks |
| HRC-45M | Superficial Rockwell | 15N/30N/45N | Sheet, plating, case layers |
| HRS-150M / XHRS-150M | Digital Rockwell | HRA/HRB/HRC | Lines needing data upload |
| HBRVS-187.5 | Brinell-Vickers-Rockwell | HBW/HRA/HRB/HRC/HV | Mixed low-volume production |
Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.
Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.
Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.
Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.
Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.
Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.