HBE-3000A Brinell Hardness Tester

Brinell Hardness Tester

ModellHBE-3000A
  • 操作方式触摸屏控制
  • 布氏标尺HBW2.5/62.5、HBW10/100、HBW5/125、HBW2.5/187.5、HBW10/250、 HBW10/500、HBW5/750、HBW10/1000、HBW10/1500、HBW10/3000
  • 试验力加载自动(加卸/保持/卸载)
  • 符合标准(精度)GB/T231.2国家标准、JJG150检定规程

By submitting you agree to our privacy policy.

01

Überblick

HBE-3000A电子布氏硬度计主要用于铸铁、钢材、有色金属及软合金等材料的硬度测定,布氏硬度试验是所有硬度试验中压痕最大的一种试验法,它能反映出材料的综合性能,不受试样组织显微偏析及成分不均匀的影响,所以它是一种精度较高的硬度试验法。在冶金、锻造、未经淬火钢及有色金属等工业领域、实验室、大专院校和科研单位内广泛使用。
产品特点:
1、本机不需要传统的砝码加载实验力,采用全电子闭环式传感器加载控制系统,高精度、高重复性和稳定性好、操作简便。
2、人性化操作界面,让使用者更方便、直观、操作更简便。
技术参数:
产品型号
HBE-3000A
操作方式
触摸屏控制
布氏标尺
HBW2.5/62.5、HBW10/100、HBW5/125、HBW2.5/187.5、HBW10/250、
HBW10/500、HBW5/750、HBW10/1000、HBW10/1500、HBW10/3000
试验力加载
自动(加卸/保持/卸载)
符合标准(精度)
GB/T231.2国家标准、JJG150检定规程
测微目镜
读数显微镜20X
最小检测单位
0.005mm
测量数据采集方式
手动采集
测量数据计算方式
手动输入测试长度,屏幕直接读取
硬度值显示方式
触摸屏显示
压头规格
直径2.5mm, 5mm, 10mm
转换标尺
内置,触摸屏转换并显示
内置打印机
无
测试储存组数
无
硬度测量范围
8-650HBW
试验力保荷时间
0-99秒(s)(每1秒(s)为一单位)
光源亮度调节
无
试件最大高度
235mm
压头中心到内壁距离
135mm(从中心算起)
大平台直径
直径200mm,厚度20mm
中平台直径
直径69mm,厚度27mm
V型台尺寸
直径69mm,开口65mm
外形尺寸
525x183x800mm
重量
130Kg
电源
AC220V/50Hz

HBE-3000A Brinell Hardness Tester supplied by CHWES. 24 key specifications available on request.

02

Technische Daten

操作方式触摸屏控制
布氏标尺HBW2.5/62.5、HBW10/100、HBW5/125、HBW2.5/187.5、HBW10/250、 HBW10/500、HBW5/750、HBW10/1000、HBW10/1500、HBW10/3000
试验力加载自动(加卸/保持/卸载)
符合标准(精度)GB/T231.2国家标准、JJG150检定规程
测微目镜读数显微镜20X
最小检测单位0.005mm
测量数据采集方式手动采集
测量数据计算方式手动输入测试长度,屏幕直接读取
硬度值显示方式触摸屏显示
压头规格直径2.5mm, 5mm, 10mm
转换标尺内置,触摸屏转换并显示
内置打印机无
测试储存组数无
硬度测量范围8-650HBW
试验力保荷时间0-99秒(s)(每1秒(s)为一单位)
光源亮度调节无
试件最大高度235mm
压头中心到内壁距离135mm(从中心算起)
大平台直径直径200mm,厚度20mm
中平台直径直径69mm,厚度27mm
V型台尺寸直径69mm,开口65mm
外形尺寸525x183x800mm
重量130Kg
电源AC220V/50Hz

* Generated by rule engine over the product database; for pre-selection only.

03

Messprinzip

Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

  • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
  • Rockwell C 150 kgf: fast batch checking of hardened parts.
  • Brinell: castings, annealed and coarse-grain materials.
  • Leeb: portable rebound testing on large parts.
04

Process animation

  1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
  2. Mount and align: place the specimen, position the indenter over the test point.
  3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
  4. Load: apply force at the set rate, dwell 10–15 s.
  5. Measure: read diagonals or depth, compute HV/HRC.
  6. Gradient: step along depth and plot hardness versus distance.
0102030405
05

Calculation & formulas

1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

06

Normen

StandardTitleScope
GB/T 4340.1-2009Vickers hardness test — test methodVickers
GB/T 230.1-2018Rockwell hardness testRockwell
GB/T 231.1-2018Brinell hardness testBrinell
ISO 6507-1Vickers hardness testExport
ASTM E92Vickers hardness of metallic materialsAmericas
GB/T 17394.1-2014Leeb hardness testPortable

Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

07

Auswahl

1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

ModelPrincipleRangeTypical use
HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

08

Prüfverfahren

Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

09

Industry applications

  • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
  • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
  • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
  • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
  • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
  • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
  • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
  • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0VergleichTechnischer Vergleich