MIC10 Hardness Tester

Hardness Tester

모델MIC10
  • 测量/转换范围20~1740HV、48~105HRB、20~68HRC、76~618HB、5~2250N/mm2(10Kg探头)
  • 显示4位LCD带开关背光
  • 分辨率1HV;1HB;5N/mm2;0.1/0.5/1HRC和HRB(可选)
  • 数据内存数据记录器可存1500个测量值,存储卡可存590个数据(MIC10DL)

By submitting you agree to our privacy policy.

01

제품 개요

一、MIC系列超声波硬度计产品简介:
超声波硬度计MIC10/MIC10DL利用UCI(Ultrasonic Contact Impedance-超声波接触阻抗)方法能快速、方便地对维氏硬度凹处进行评价,无需使用显微镜。小而轻的MIC 10使用电池供电,可在现场快速使用,在各方面不受限制,甚至可用在端头位置。该仪器可适用于任何形状、尺寸的大多数细晶粒、材料,特别适合于小公差范围内确定材料特性。可测量的工件部位包括法兰盘边缘和齿轮根部,也可在任何方向测量,如水平或垂直向上。
二、MIC系列超声波硬度计仪器特点:
1、高精度测量:由于连续频率测量在进入测量表面的穿透过程中得到监控;
2、硬度值的变化和显示:单位HV、HB、HRC、HRB和抗拉强度N/mm2;
3、MIC10DL为存储型,配备有内部存储器和附加存储卡
·内部数据记录器可记录约1500个测量值,另有存储卡可存储约590个测量值;
·可打印静态指示功能(最大读数、最小读数、绝对和相对标准偏差)
·RS232接口可通过计算机机遥控或通过打印机可将检测结果存档。
三、MIC系列超声波硬度计技术参数:
1、测量/转换范围:20~1740HV、48~105HRB、20~68HRC、76~618HB、5~2250N/mm2(10Kg探头)
2、显示:4位LCD带开关背光
3、分辨率 :1HV;1HB;5N/mm2;0.1/0.5/1HRC和HRB(可选)
4、数据内存:数据记录器可存1500个测量值,存储卡可存590个数据(MIC10DL)
5、接口:RS232接口,可用于打印机和计算机双向通讯(MIC10DL)
6、电源:2节1.5V电池
7、尺寸重量:160x70x45mm,300g
四、MIC系列超声波硬度计探头和附件:
1、手动标准探头MIC201A:10N/1Kgf负载,特别适用于小凹槽表面
2、手动标准探头MIC205A:50N/5Kgf负载,适用于大多数的应用
3、手动标准探头MIC2010A:100N/10Kgf负载,适用于粗晶粒材料和粗糙表面
4、手动短探头MIC201AS(10N/1Kgf负载)/MIC205AS(50N/5Kgf负载)
5、手动长探头MIC201AL(10N/1Kgf负载)/MIC205AL(50N/5Kgf负载),配备有一个较长的振荡棒(37mm)。用于测量轮廓表面,或工件结构深的内腔/凹槽中。如蜗杆齿轮和啮合齿轮。
6、电动探头MIC2103A(3N/0.3Kgf)、MIC211A(大约8N/0.8Kgf)和电动探头MIC2101A(1N/0.1Kgf),配置有电动控制的维氏硬度计金刚石,能获得可靠的测量结果。
五、MIC系列超声波硬度计探头和附件:
型号
负载
探头直径
探头长度
手动标准探头MIC201A
手动标准探头MIC205A
手动标准探头MIC2010A
1kgf
5kgf
10kgf
19mm
162mm
手动长探头MIC201AL
手动长探头MIC205AL
1kgf
5kgf
19mm
190mm
手动短探头MIC201AS
手动短探头MIC205AS
1kgf
5kgf
19mm
90mm

MIC10 Hardness Tester supplied by CHWES. 7 key specifications available on request.

02

사양

测量/转换范围20~1740HV、48~105HRB、20~68HRC、76~618HB、5~2250N/mm2(10Kg探头)
显示4位LCD带开关背光
分辨率1HV;1HB;5N/mm2;0.1/0.5/1HRC和HRB(可选)
数据内存数据记录器可存1500个测量值,存储卡可存590个数据(MIC10DL)
接口RS232接口,可用于打印机和计算机双向通讯(MIC10DL)
电源2节1.5V电池
尺寸重量160x70x45mm,300g

* Generated by rule engine over the product database; for pre-selection only.

03

측정 원리

Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

  • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
  • Rockwell C 150 kgf: fast batch checking of hardened parts.
  • Brinell: castings, annealed and coarse-grain materials.
  • Leeb: portable rebound testing on large parts.
04

Process animation

  1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
  2. Mount and align: place the specimen, position the indenter over the test point.
  3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
  4. Load: apply force at the set rate, dwell 10–15 s.
  5. Measure: read diagonals or depth, compute HV/HRC.
  6. Gradient: step along depth and plot hardness versus distance.
0102030405
05

Calculation & formulas

1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

06

규격

StandardTitleScope
GB/T 4340.1-2009Vickers hardness test — test methodVickers
GB/T 230.1-2018Rockwell hardness testRockwell
GB/T 231.1-2018Brinell hardness testBrinell
ISO 6507-1Vickers hardness testExport
ASTM E92Vickers hardness of metallic materialsAmericas
GB/T 17394.1-2014Leeb hardness testPortable

Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

07

선택 가이드

1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

ModelPrincipleRangeTypical use
HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

08

시험 방법

Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

09

Industry applications

  • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
  • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
  • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
  • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
  • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
  • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
  • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
  • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0비교사양 비교