제품

Testing Machines

Universal, servo, tribology

WDS class-0.5 electronic universal, WAW servo-hydraulic and WEW/WES hydraulic machines from 1 to 2000 kN, plus MM-series tribometers (four-ball, ring-on-block, face, reciprocating, high-temperature) for metals, fasteners, composites and lubricants.

Universal, servo, tribology

Testing Machines · 49 모델

01

측정 원리

Testing Machines

A universal testing machine comprises the load frame, drive system, load cell, displacement/extensometer measurement and closed-loop control. A servo motor and screw drive the crosshead (or a servo valve drives the actuator); the load cell converts force to a signal, the extensometer measures strain over the gauge length, and the controller follows the programmed rate while logging force–displacement–strain.

Software derives upper and lower yield strength (ReH/ReL), tensile strength Rm, elongation A, reduction of area Z and modulus E. Control modes include speed, force, displacement and strain; GB/T 228.1-2021 requires strain control in the yield region (method A) for lower uncertainty.

  • Electromechanical: 1–600 kN for metals, plastics and composites.
  • Servo-hydraulic: 300–2000 kN for high-strength steel, fasteners and bars.
  • Specialised: friction and wear, impact, bend, peel.
02

Process animation

Testing Machines

  1. Measure width and thickness (or diameter) at three points; compute S₀.
  2. Clamp with wedge or hydraulic grips, aligned to avoid bending.
  3. Extensometer attached to the gauge length, zeroed.
  4. Load: speed control in the elastic range, strain control at yield, speed control in hardening.
  5. Fracture: detect peak and break, stop.
  6. Report: ReH/ReL/Rm/A/Z with curves and data tables.
0102030405
03

Calculation & formulas

Testing Machines

1. Tensile strength: Rm = Fmax/S0; a 10 mm bar (S0=78.5 mm²) breaking at 62.8 kN gives Rm ≈ 800 MPa.

2. Yield: Rp0.2 is interpolated from the extensometer curve at 0.2% non-proportional extension.

3. Elongation & reduction: A = (Lu−L0)/L0; Z = (S0−Su)/S0; L0=50, Lu=62.5 mm → A = 25%.

4. Friction coefficient: μ = F/N; at N = 100 N and F = 32 N, μ = 0.32. Four-ball results report PB (last non-seizure) and PD (weld) loads.

5. Wear rate: k = V/(F·s); obtain V from Δm/ρ. Typical specific wear rates run 10⁻⁸–10⁻⁶ mm³/(N·m).

04

규격

Testing Machines

StandardTitleScope
GB/T 228.1-2021Metallic materials — tensile testing, room temperatureTension
ISO 6892-1Tensile testing at room temperatureExport projects
ASTM E8/E8MTension testing of metallic materialsAmericas
GB/T 7314-2017Compression testing at room temperatureCompression
GB/T 232-2010Bend testing of metallic materialsBending
GB/T 3098.1-2010Mechanical properties of fastenersFasteners
05

선택 가이드

Testing Machines

1. Frame capacity plus 20–30%: Φ32 rebar yields near 630 kN so choose 1000 kN; M30 proof load is about 550 kN so choose 600–1000 kN. Running at full scale accelerates load-cell fatigue.

2. Servo-hydraulic or electromechanical: ≥300 kN with high stiffness and long stroke (rebar, bolts, concrete) needs servo-hydraulic (WAW/WEW); ≤300 kN with tight speed control (plastics, composites) suits electromechanical frames (WDS).

3. Display, digital or PC-controlled: a digital readout for single values; PC control (the -C suffix) for stress-strain curves, reports and batch data.

4. Fixtures often matter more than the frame: ribbed grips for rebar, proof-load fixtures for bolts, wrap grips for cables. Poor alignment costs 2–3 percentage points of elongation.

5. Extensometers and options: contact or video extensometers for modulus, high-temperature furnaces and extensometers, large platens with displacement control for battery crush.

6. Foundation and safety: a 1000 kN frame needs an isolated concrete base, guard doors and e-stops; hydraulic units need oil-temperature management.

SeriesTypeForce rangeTypical specimens
WDS-1G to 300GElectromechanical1–300 kNPlastics, composites, small parts
WEW-100D to 1000DHydraulic, digital100–1000 kNRebar, bolts, metals
WEW-300C to 2000CHydraulic, PC300–2000 kNHigh-strength bolts, forgings
WAW-100 to 1000Servo-hydraulic100–1000 kNRate-controlled acceptance
WAW-300C to 2000CServo-hydraulic, PC300–2000 kNBridges, nuclear components
WES-300C to 2000CCompression300–2000 kNConcrete, blocks
MMW-1A / MRS-10WFriction and wear—Lubricants, coatings

Three acceptance checks: verify force at 20/50/80% with a standard load cell; check alignment so a standard specimen breaks mid-gauge; run three identical specimens and look at scatter.

06

시험 방법

Testing Machines

Specimen. Proportional (L₀ = 5.65√S₀) or non-proportional specimens to GB/T 228.1; transition radius R ≥ 5 mm; Ra ≤ 1.6 µm with work-hardened layers removed.

Measurement. Width and thickness at three positions within the gauge length, use the minimum for S₀; below 1 mm use optical or 0.001 mm micrometers.

Loading. 5–30 MPa/s in the elastic range, 0.00025/s strain rate at yield per method A, up to 0.0067/s in hardening; log at 100 Hz or more to catch yield serrations.

Evaluation. ReH is the first peak, ReL the lowest point, Rm the maximum force over S₀, A from the final gauge length (offset method), Z from the minimum fracture diameter.

Quality control. Daily check with a reference specimen, monthly force calibration with a class 0.3 proving instrument, half-yearly extensometer calibration, 23 ± 5 °C.

07

Industry applications

Testing Machines

  • Construction and bridges: rebar tensile and bend, high-strength bolt wedge load, strand relaxation, concrete compression, with loading-rate control to GB/T 228.1 and GB/T 3098.1.
  • Metals and forgings: room and elevated temperature tensile, yield strength, elongation and reduction of area for material verification.
  • Automotive parts: chassis tension-compression, suspension springs, seat-belt anchorages, battery-pack crush with dedicated fixtures.
  • Fasteners: proof load, nut proof load, washer elasticity; fixture alignment drives scatter.
  • Plastics and composites: tension, flexure, compression and shear on low-force frames (WDS) with non-contact extensometers.
  • Cables and ropes: breaking force and elongation with long stroke and large-deformation grips.
  • Friction and wear: MMW/MRS four-ball, reciprocating and ring-block tests for lubricants and coatings.
  • Third-party testing: calibrated frames with tamper-evident data and raw curve export.
적용 사례

적용 사례

전체 보기→

Price and lead time for this model

엔지니어가 1영업일 내에 선정안, 검사 기준, 납기를 제안합니다.

⇄0비교사양 비교