HOT
BIAS-500 · 2026-11-17 · +86 21 5748 2007
BIAS-500 Biological Microscope
Biological Microscope
- 系统放大倍数800~3200X(19寸显示器)
- 光学放大倍数100X~400X
- 机械筒长∞
- 物镜共轭距离∞
By submitting you agree to our privacy policy.
제품 개요
BIAS-500偏光调制相衬生物显微镜分析系统适合于对细胞组织,透明液态组织的显微观察,也可对培养皿中的培养组织进行动态显微观察。可应用于科研院所、高等院校、医疗卫生、检验检疫、农牧乳业等部门。
BIAS-500偏光调制相衬生物显微镜分析系统是将传统光学生物显微镜与计算机或数码相机通过光学技术、电子技术、软件技术等结合在一起的高端生物显微分析系统,出了具备生物显微镜的一般性能外,还具备了数据分析、保存、编辑、打印等功能,同时更方便和更直观的对微观状态进行科学实验。该系统配备了研润自主研发的BIAS测量分析系统以及BOS高端光学系统。
一、主机技术参数:
系统放大倍数:800~3200X(19寸显示器);
光学放大倍数:100X~400X;
机械筒长:∞;
物镜共轭距离:∞;
目镜:大视野WF10X(Φ22mm)、对中目镜;
目镜:铰链双目,观察角度为45度,瞳距为48~75mm,眼点高度高于台面400mm;
目镜接口:Ф30mm;
齐焦距离:10mm;
明场物镜(盖玻片厚度1.2mm):10X/0.25\工作距离4.27mm,20X/0.4\8.0mm,40X/0.6\3.5mm;
相衬物镜PHP2(盖玻片厚度1.2mm):10X/0.25\工作距离4.27mm;
转换器:五孔转换器;
调焦机构:粗微动同轴, 微动格值:2μ, 粗动松紧可调,带锁紧和限位装置,有效调焦行程11mm;
长工作距离聚光镜:长工作距离聚光镜,工作距离70mm,带插板式相衬装置;
载物台:224*208mm;移动范围112*79mm,移动尺可拆卸;
培养皿托板一:86mm(宽)X129.5mm(长),可适配圆形培养皿Ф87.5mm;
培养皿托板二:34mm(宽)X77.5mm(长),可适配圆形培养皿Ф68.5mm;
培养皿托板三:57mm(宽)X82mm(长);
相位相衬系统:拉板式相衬聚光镜,相衬环中心可调;
光源:9W/LED,亮度可调;
滤色片:磨砂玻璃、蓝滤色片;
调校工具:M4、M5内六角扳手;
配备系统:主机、BIAS数据分析系统、BOS光学系统、品牌电脑、CCD、接口等;
二、生物分析系统功能:
1、基本模块:图像采集,处理,几何测量,定倍打印,图像拼接等基本功能;
2、选配模块:
2.1、菌群分析:能够分析出每个菌群的长轴、短轴、直径、面积和计算出菌群的统计数据以及最大面积的菌群参数,分析比较大的菌群内部的颗粒情况,;
2.2、细胞分析:可分析出每个细胞的长轴、短轴、周长、面积,计算出细胞的统计数据以及最大面积细胞的参数;
2.3、图像叠加:搜索出第一张生物图像上被观察对象的轮廓,然后装入第二张图像,软件将第一张搜索出的轮廓线投影到第二张图像上,同时计算出每个轮廓线投影范围的长轴、短轴、周长、面积、像素个数、平均灰度等参数,自动算出叠加区间内的参数;
2.4、免疫组化:提取各个成份的基本色,并设置容差范围,软件搜索出该成分在图像上对应的面积、百分比、颗粒数、平均灰度等参数,可一次性分析8种成份;
2.5、成份分析:提取各个成份的基本色,并设置容差范围,软件搜索出该成份在图像上对应的面积、百分比、颗粒数、平均灰度等参数,可一次性分析40种成份;
2.6、颗粒分析:提取颗粒的基本色,设置容差范围,软件搜索出该成份在图像上对应的长轴、短轴、直径、面积、周边色等参数;
三、选购荧光分析系统功能:
1、颜色通道:可分析蓝、绿、红、灰等四种通道的荧光图像;
2、细胞分析:可用阈值分割的方式提取出细胞的轮廓;
3、细胞分割:可一键分割出黏连细胞;
4、细胞分析完成后,系统自动算出每个细胞的形态学参数;
5、融合图像:载入保存的通道图像,进行2个通道以上的图像融合;
6、自动计算细胞的重合情况;
7、可利用自动载物台进行图像的自动拼接;
四、选购偏光分析系统功能:
1、基本模块:图像采集、图像处理、几何测量、定倍打印、图像拼接;
2、选购模块:
2.1、粒度分析(手动测量直径法):测量颗粒的直径,算出最大、最小、平均直径,自动生成累积曲线(调整)、累积曲线(线性)、直方图、频率曲线等4种曲线,可保存和载入测量的过程;
2.2、空隙特征分析(手动测量面积法):可以得出空隙面积,自动算出孔隙率,可保存和载入测量过程;
2.3、岩石薄片粒度分析(自动计算):选择六种颗粒颜色,搜索出想要分析的颗粒,计算出颗粒百分比,同时算出颗粒总数、颗粒平均直径、平均截面积、平均截距、弗里特直径、最小直径、最大直径、平均短轴长、长宽比大于0.5的颗粒比等数据;
2.4、铸铁薄片空隙特征分析(自动计算):搜索出想要的空隙,自动算出孔隙率、自动算出空隙总数、最大空隙半径、最小空隙半径、平均空隙半径等值;
2.5、金刚石图像分析(自动计算):搜索出想要的金刚石颗粒,软件自动算出金刚石的面积百分比,同时算出空隙总数、最大空隙半径、最小空隙半径、平均空隙半径等值;
2.6、粒度分析(颜色提取法):选取6种颜色的颗粒,搜索出想要的颗粒,计算出颗粒百分比,同时算出颗粒总数、平均直径、平均截面积、平均截距、弗里特直径等值;
2.7、孔隙特征分析(颜色提取法):选择6中想要的空隙颜色,算出孔隙率,同时算出空隙总数、最大半径、最小半径、平均半径等值;
2.8、矿物成份百分比测定(图形分析):选择8种成份的颜色,设置每种成份的容差,软件搜索出对应的阻止,并算出面积和面积百分比,可分析单图也可以分析指定目录下的所有图像;
2.9、矿物成份百分比测定(魔术棒):用魔术棒在岩石图像上选择需要分析的组织,算出面积和面积百分比;
2.10、颗粒扫描细分:可同时搜索出黑色和白色两种颗粒,并算出每个颗粒的周长、面积、长轴、短轴、直径、形状比、颗粒类别等;
BIAS-500 Biological Microscope supplied by CHWES. 22 key specifications available on request.
사양
| 系统放大倍数 | 800~3200X(19寸显示器) |
|---|---|
| 光学放大倍数 | 100X~400X |
| 机械筒长 | ∞ |
| 物镜共轭距离 | ∞ |
| 目镜 | 大视野WF10X(Φ22mm)、对中目镜 |
| 目镜接口 | Ф30mm |
| 齐焦距离 | 10mm |
| 明场物镜(盖玻片厚度1.2mm) | 10X/0.25\工作距离4.27mm,20X/0.4\8.0mm,40X/0.6\3.5mm |
| 相衬物镜PHP2(盖玻片厚度1.2mm) | 10X/0.25\工作距离4.27mm |
| 转换器 | 五孔转换器 |
| 调焦机构 | 粗微动同轴, 微动格值:2μ, 粗动松紧可调,带锁紧和限位装置,有效调焦行程11mm |
| 长工作距离聚光镜 | 长工作距离聚光镜,工作距离70mm,带插板式相衬装置 |
| 载物台 | 224*208mm;移动范围112*79mm,移动尺可拆卸 |
| 培养皿托板一 | 86mm(宽)X129.5mm(长),可适配圆形培养皿Ф87.5mm |
| 培养皿托板二 | 34mm(宽)X77.5mm(长),可适配圆形培养皿Ф68.5mm |
| 培养皿托板三 | 57mm(宽)X82mm(长) |
| 相位相衬系统 | 拉板式相衬聚光镜,相衬环中心可调 |
| 光源 | 9W/LED,亮度可调 |
| 滤色片 | 磨砂玻璃、蓝滤色片 |
| 调校工具 | M;M5内六角扳手 |
| 配备系统 | 主机、BIAS数据分析系统、BOS光学系统、品牌电脑、CCD、接口等 |
| 基本模块 | 图像采集,处理,几何测量,定倍打印,图像拼接等基本功能 |
* Generated by rule engine over the product database; for pre-selection only.
측정 원리
The metallurgical microscope uses an infinity-corrected optical path with reflected Köhler illumination. Light passes the collector, field stop and aperture stop, is deflected by a semi-transparent mirror through the objective onto the specimen, and returns through the same objective to the eyepiece or camera.
- Bright field for routine microstructure, inclusions and decarburised layers.
- Dark field collects scattered light to reveal grain boundaries, cracks and non-metallic inclusions.
- Polarised light identifies anisotropic phases, spheroidised structures and coating stress.
- DIC converts tiny height differences into contrast, ideal for polished, unetched samples.
Objectives of 5× to 100× are combined with 10× eyepieces. Higher numerical aperture gives better resolution but shallower depth of field.
Process animation
- Sampling and preparation: sectioning, mounting, grinding, polishing, etching.
- Illumination and focus: select BF/DF/POL/DIC and focus.
- Image capture: trinocular port, 1× camera adapter, white balance.
- Scale calibration: calibrate µm per pixel with a stage micrometer.
- Measurement: grain size, case depth, coating thickness, inclusion rating.
Calculation & formulas
1. System magnification: M = objective × eyepiece × adapter, e.g. 40× / 10× / 1× = 400×.
2. Resolution: d = 0.61λ/NA (λ≈550 nm). A 40× objective with NA 0.65 resolves 0.52 µm; an NA 0.95 dry objective reaches 0.35 µm.
3. Depth of field scales with λ/NA² — higher NA, shallower depth; use low NA for fracture surfaces.
4. Grain size (GB/T 6394): at 100×, grains N per 645 mm² field follow N = 2G−1; counting 128 grains gives G = log2128 + 1 = 8. Intercept method: mean intercept L̄ = line length ÷ intercepts, G = −6.6437 lg L̄ (mm, 100×).
5. Effective case depth: distance to 550 HV1, fitted from a micro-hardness traverse and averaged over three positions.
규격
| Standard | Title | Scope |
|---|---|---|
| GB/T 13298-2015 | Metallic materials — examination of microstructure | Microstructure rating |
| GB/T 6394-2017 | Determination of average grain size | Grain size |
| ASTM E3-11 | Guide for metallographic specimen preparation | Preparation |
| ASTM E112 | Determining average grain size | Grain size |
| ISO 643 | Steels — micrographic determination of grain size | Grain size |
Export projects often require dual GB and ASTM reports; the software ships both rating charts.
선택 가이드
1. Surface or cross-section: stereo microscopes (HX-ZG7, XSZ) for fracture surfaces, solder joints and coatings; upright or inverted metallurgical microscopes (HX-4, HX-G series) for microstructure, case depth and inclusions.
2. Upright or inverted: upright for small specimens that are flipped often; inverted (HX-G3A/G4C/G5A) for large, heavy parts such as gears, shafts and tube sections that go straight onto the stage without re-mounting.
3. Optics set the ceiling: plan achromats cover routine rating; semi-apochromats or apochromats with a research stand (HX-G5A) are needed for 1000× precipitates and brightfield/darkfield/polarised switching.
4. Three levels of digitalisation: a 5 MP camera for images; camera plus analysis software (grain size, case depth, inclusions, porosity) for automatic rating and reports; motorised stage with scanning and stitching for unattended batches.
5. Do not forget accessories: polariser, darkfield, DIC, and a microhardness interface.
6. Room: an anti-vibration bench at 20±3 °C for research stands; keep preparation and microscopy rooms separate to avoid abrasive dust.
| Series | Type | Typical task | Recommended setup |
|---|---|---|---|
| HX-4A / HX-4B | Upright metallurgical | Routine structure, case depth | 5×/10×/40× + 5 MP camera |
| HX-G2A / G2B | Inverted | Batch samples, no re-mounting | Brightfield + simple polariser |
| HX-G3A | Trinocular inverted | Case depth, rating, reports | Camera + analysis software |
| HX-G4C / G5A | Research inverted | Darkfield/polarised/DIC | Semi-apochromat + motorised stage |
| HX-ZG7 / XSZ-146 | Stereo | Fracture, solder, low-mag locating | Zoom + ring light |
Common misconceptions: higher magnification is not better (numerical aperture limits resolution, 100× dry is the practical ceiling); ignoring stage travel so large samples do not fit; buying the stand without software and still rating by eye, which kills repeatability.
시험 방법
Preparation. Section perpendicular to the feature of interest. Keep hot-mounting below 150 °C for aluminium and quenched parts, or use cold mounting. Grind 320→600→800→1200, removing previous scratches at each step; polish with 3 µm then 1 µm diamond. Etchants: 4% nital for carbon steel (3–8 s), aqua regia or electrolytic for stainless, Keller for aluminium.
Examination. Locate a representative field at 5×/10×, then switch to higher power. Rate grain size to GB/T 6394 by comparison or intercept. Measure case depth at 500× with an ocular scale or calibrated software, averaging five readings.
Calibration. Verify µm/pixel daily with a stage micrometer, check against a certified specimen quarterly, record three fields per sample and archive images with scale bars.
Pitfalls. Over-etching widens boundaries and fakes decarburisation; residual scratches can be mistaken for cracks; rounded mounting edges inflate case depth. Keep an unetched specimen for coating and crack review.
Industry applications
- Steel and heat treatment: decarburised depth, carburised/nitrided case depth, grain size (GB/T 6394), non-metallic inclusions (GB/T 10561), banding and Widmanstätten rating.
- Non-ferrous metals: aluminium grain and recrystallisation, alpha/beta ratio in brass, twinning and corrosion morphology in magnesium.
- Welding and brazing: penetration, HAZ width, porosity and cracks, intermetallic thickness at dissimilar joints.
- Additive manufacturing: porosity, lack-of-fusion defects, melt-pool morphology in SLM parts, porosity repeatability within 0.2%.
- Bearings and gears: martensite rating, retained austenite, carbide network and banding, grinding burn and white layer.
- Electronics: IMC thickness, plating cross-sections, PCB micro-sections, gold wire ball bonds (stereo plus metallurgical).
- Powders and ceramics: particle morphology and size, sintered porosity, coating cross-section thickness.
- Failure analysis: fracture surface macro and micro morphology, corrosion products, crack path and origin, with stereo microscopy for low-magnification locating.


