HOTHMAS-D5/10/30/50SZA Vickers Hardness Tester
Vickers Hardness Tester
- 测量分析系统HMAS‑硬度测量分析系统
- 光学成像系统维氏硬度大三通光学成像系统
HMAS-D1000SZA · 2026-11-17 · +86 21 5748 2007
Micro Vickers Hardness Tester
By submitting you agree to our privacy policy.
HMAS-D1000SZA
自动显微硬度测量系统专为金属及部分非金属材料的显微维氏硬度测定而设计,集光学成像、精密位移与智能控制于一体,可自动完成压痕数字成像与读数。适用于机加工件、锻件、铸铁、铸钢等材质,亦可精准评估有效硬化层深度、涂镀层结合力及焊接热影响区硬度,同时实现对内部金相组织的高清观察与图像采集。
技术参数:
型号
HMAS‑D1000SZA
测量分析系统
HMAS硬度测量分析系统
光学成像系统
显微硬度大三通光学成像系统
转塔方式
自动转塔
升降机构
精密梯形丝杆
变荷装置机构
齿轮垂直加载
试验力
(8 级) N: 0.098N、0.245N、0.490N、0.981N、1.961N、2.942N、4.903N、9.807N; (8 级) gf:
10gf、25gf、50gf、100gf、200gf、300gf、500gf、1000gf; (8 级) 标尺:
HV0.01、HV0.025、HV0.05、HV0.1、HV0.2、HV0.3、HV0.5、HV1
转换标尺
HV、HK、HBW、HRA、HRB、HRC、HRD、HRF、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T
聚焦方式
手动
X/Y 平台
自动
Z 轴升降
手动
硬度打压
电脑控制
梯度测试
电脑控制(自动连续打压)
硬度测量
连打连测 + 单点自动 / 手动(多测量系统)
光源调节
电脑控制
长度测量
电脑自动
测试定点
自动导航定位 / 路径自动定位
基点补偿
自动
断裂韧性
软件计算
放大倍数
(23 寸屏) 10X 物镜,总放大倍数约 320X;40X 物镜,总放大倍数约 1200 倍
理论硬度测量范围
8‑3000HV
试验力加载
全自动(加载 / 保荷 / 卸载)
执行国家标准
GB/T4340 国家标准,ISO6507 质量认证,ASTM 标准
X‑Y 移动平台
试台尺寸:140*180mm,移动范围50*50mm,最小步距0.1μm
硬度值显示方式
(双系统测量) 主机单独测量 / 电脑软件测量分析
主机最小检测单位
0.025μm
试验力保持时间
0‑60 秒,最小变动量 1 秒
试件最大高度
135mm
压头中心到内壁距离
170mm
电源电压
AC 220V/50Hz
外形尺寸
220*570*680mm(长*宽*高)
净重
46.0kg
毛重
61.0kg
HMAS-D1000SZA Micro Vickers Hardness Tester supplied by CHWES. 32 key specifications available on request.
| 测量分析系统 | HMAS硬度测量分析系统 |
|---|---|
| 光学成像系统 | 显微硬度大三通光学成像系统 |
| 转塔方式 | 自动转塔 |
| 升降机构 | 精密梯形丝杆 |
| 变荷装置机构 | 齿轮垂直加载 |
| 试验力 | (8 级) N: 0.098N、0.245N、0.490N、0.981N、1.961N、2.942N、4.903N、9.807N; (8 级) gf: 10gf、25gf、50gf、100gf、200gf、300gf、500gf、1000gf; (8 级) 标尺: HV0.01、HV0.025、HV0.05、HV0.1、HV0.2、HV0.3、HV0.5、HV1 |
| 转换标尺 | HV、HK、HBW、HRA、HRB、HRC、HRD、HRF、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T |
| 聚焦方式 | 手动 |
| X/Y 平台 | 自动 |
| Z 轴升降 | 手动 |
| 硬度打压 | 电脑控制 |
| 梯度测试 | 电脑控制(自动连续打压) |
| 硬度测量 | 连打连测 + 单点自动 / 手动(多测量系统) |
| 光源调节 | 电脑控制 |
| 长度测量 | 电脑自动 |
| 测试定点 | 自动导航定位 / 路径自动定位 |
| 基点补偿 | 自动 |
| 断裂韧性 | 软件计算 |
| 放大倍数 | (23 寸屏) 10X 物镜,总放大倍数约 320X;40X 物镜,总放大倍数约 1200 倍 |
| 理论硬度测量范围 | 8‑3000HV |
| 试验力加载 | 全自动(加载 / 保荷 / 卸载) |
| 执行国家标准 | GB/T4340 国家标准,ISO6507 质量认证,ASTM 标准 |
| X‑Y 移动平台 | 试台尺寸:140*180mm,移动范围50*50mm,最小步距0.1μm |
| 硬度值显示方式 | (双系统测量) 主机单独测量 / 电脑软件测量分析 |
| 主机最小检测单位 | 0.025μm |
| 试验力保持时间 | 0‑60 秒,最小变动量 1 秒 |
| 试件最大高度 | 135mm |
| 压头中心到内壁距离 | 170mm |
| 电源电压 | AC 220V/50Hz |
| 外形尺寸 | 220*570*680mm(长*宽*高) |
| 净重 | 46.0kg |
| 毛重 | 61.0kg |
* Generated by rule engine over the product database; for pre-selection only.
Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.
Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.
1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.
2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.
3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.
4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.
5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.
| Standard | Title | Scope |
|---|---|---|
| GB/T 4340.1-2009 | Vickers hardness test — test method | Vickers |
| GB/T 230.1-2018 | Rockwell hardness test | Rockwell |
| GB/T 231.1-2018 | Brinell hardness test | Brinell |
| ISO 6507-1 | Vickers hardness test | Export |
| ASTM E92 | Vickers hardness of metallic materials | Americas |
| GB/T 17394.1-2014 | Leeb hardness test | Portable |
Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.
1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.
2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.
3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.
4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.
5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.
6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.
| Model | Principle | Range | Typical use |
|---|---|---|---|
| HRC-150SMJ | Rockwell, motorised digital | HRA/HRB/HRC | Batch sampling in heat treatment |
| HRC-150SM / HRC-150M | Rockwell | HRA/HRB/HRC | Incoming and in-process checks |
| HRC-45M | Superficial Rockwell | 15N/30N/45N | Sheet, plating, case layers |
| HRS-150M / XHRS-150M | Digital Rockwell | HRA/HRB/HRC | Lines needing data upload |
| HBRVS-187.5 | Brinell-Vickers-Rockwell | HBW/HRA/HRB/HRC/HV | Mixed low-volume production |
Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.
Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.
Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.
Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.
Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.
Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.