HOTWEW300-600B Hydraulic Universal Testing Machine
Hydraulic Universal Testing Machine
- 最大试验力100KN / 300KN / 600KN / 1000KN
- 测试范围5-100KN / 12-300KN / 50-600KN / 50-1000KN
WES-300B · 2026-11-17 · +86 21 5748 2007
Hydraulic Universal Testing Machine
By submitting you agree to our privacy policy.
WES-B系列液压式万能试验机用于各种金属材料的拉伸、压缩、弯曲,增加剪切附具可做剪切试验,亦可用作塑料、混凝土、水泥等非金属材料的压缩试验,增加简单附件,可完成胶带链条,钢丝绳、电焊条、瓦及构件的多种性能试验。
油缸采用:下置式主机,拉伸空间位于主机的上方,压缩、弯曲试验空间位于主机下横梁和工作台之间。
传动系统采用:下横梁升降电机经减速器、链传动机构、丝杠副传动,实现拉伸、压缩空间的调整。
液压系统采用:油箱内的油经过过滤油网被吸入油泵后,经油泵的输油管送到送油阀内,当送油手轮关闭时,由于油压作用而将活塞推开,油从回油管流回油箱,当送油手轮打开时,则油液经由油管进入工作油缸内,再通过压力油管经过回油阀体流回油箱。
控制系统采用:电子测力,液晶显示试验力-时间曲线、试验力、试验力峰值、具有明显屈服特征材料的屈服力,实验数据方便直观;通过数字健输入试样编号、横截面积,可直接测定材料的抗拉强度、屈服强度等力学性能;在配有微型打印机的情况下可对实验结果查询和打印。
保护系统采用:当试验力超过最大试验力的3%时,过载保护,油泵电机停机;当活塞升起达到上极限位置时,行程保护,油泵电机停机。
尤其适用于工程施工部门。
二.液压式万能试验机性能特点:
1.下置式主机,高度低、重量轻,性价比高。
2.液晶数显,操作方便,数据读取方便直观。
3.电子测力,分辨率高达0.01KN。
4.过载保护和行程保护,有效保护电机的正常运转。
5.简单可靠方便的液压系统。
6.可定制试验机主机颜色。
技术参数:
产品型号
WES-300B
最大试验力
300kN
量程
全程不分档,等效3档
测力范围
4%~100%FS
试验力示值相对误差
≤±1%
试验力分辨力
0.01kN
拉伸空间(mm)
550
压缩空间(mm)
380
夹持方式
手动夹紧
圆试样夹持直径(mm)
Φ6~26
扁试样夹持厚度(mm)
0~15
扁试样最大夹持宽度(mm)
70
WES-300B Hydraulic Universal Testing Machine supplied by CHWES. 11 key specifications available on request.
| 最大试验力 | 300kN |
|---|---|
| 量程 | 全程不分档,等效3档 |
| 测力范围 | 4%~100%FS |
| 试验力示值相对误差 | ≤±1% |
| 试验力分辨力 | 0.01kN |
| 拉伸空间(mm) | 550 |
| 压缩空间(mm) | 380 |
| 夹持方式 | 手动夹紧 |
| 圆试样夹持直径(mm) | Φ6~26 |
| 扁试样夹持厚度(mm) | 0~15 |
| 扁试样最大夹持宽度(mm) | 70 |
* Generated by rule engine over the product database; for pre-selection only.
A universal testing machine comprises the load frame, drive system, load cell, displacement/extensometer measurement and closed-loop control. A servo motor and screw drive the crosshead (or a servo valve drives the actuator); the load cell converts force to a signal, the extensometer measures strain over the gauge length, and the controller follows the programmed rate while logging force–displacement–strain.
Software derives upper and lower yield strength (ReH/ReL), tensile strength Rm, elongation A, reduction of area Z and modulus E. Control modes include speed, force, displacement and strain; GB/T 228.1-2021 requires strain control in the yield region (method A) for lower uncertainty.
1. Tensile strength: Rm = Fmax/S0; a 10 mm bar (S0=78.5 mm²) breaking at 62.8 kN gives Rm ≈ 800 MPa.
2. Yield: Rp0.2 is interpolated from the extensometer curve at 0.2% non-proportional extension.
3. Elongation & reduction: A = (Lu−L0)/L0; Z = (S0−Su)/S0; L0=50, Lu=62.5 mm → A = 25%.
4. Friction coefficient: μ = F/N; at N = 100 N and F = 32 N, μ = 0.32. Four-ball results report PB (last non-seizure) and PD (weld) loads.
5. Wear rate: k = V/(F·s); obtain V from Δm/ρ. Typical specific wear rates run 10⁻⁸–10⁻⁶ mm³/(N·m).
| Standard | Title | Scope |
|---|---|---|
| GB/T 228.1-2021 | Metallic materials — tensile testing, room temperature | Tension |
| ISO 6892-1 | Tensile testing at room temperature | Export projects |
| ASTM E8/E8M | Tension testing of metallic materials | Americas |
| GB/T 7314-2017 | Compression testing at room temperature | Compression |
| GB/T 232-2010 | Bend testing of metallic materials | Bending |
| GB/T 3098.1-2010 | Mechanical properties of fasteners | Fasteners |
1. Frame capacity plus 20–30%: Φ32 rebar yields near 630 kN so choose 1000 kN; M30 proof load is about 550 kN so choose 600–1000 kN. Running at full scale accelerates load-cell fatigue.
2. Servo-hydraulic or electromechanical: ≥300 kN with high stiffness and long stroke (rebar, bolts, concrete) needs servo-hydraulic (WAW/WEW); ≤300 kN with tight speed control (plastics, composites) suits electromechanical frames (WDS).
3. Display, digital or PC-controlled: a digital readout for single values; PC control (the -C suffix) for stress-strain curves, reports and batch data.
4. Fixtures often matter more than the frame: ribbed grips for rebar, proof-load fixtures for bolts, wrap grips for cables. Poor alignment costs 2–3 percentage points of elongation.
5. Extensometers and options: contact or video extensometers for modulus, high-temperature furnaces and extensometers, large platens with displacement control for battery crush.
6. Foundation and safety: a 1000 kN frame needs an isolated concrete base, guard doors and e-stops; hydraulic units need oil-temperature management.
| Series | Type | Force range | Typical specimens |
|---|---|---|---|
| WDS-1G to 300G | Electromechanical | 1–300 kN | Plastics, composites, small parts |
| WEW-100D to 1000D | Hydraulic, digital | 100–1000 kN | Rebar, bolts, metals |
| WEW-300C to 2000C | Hydraulic, PC | 300–2000 kN | High-strength bolts, forgings |
| WAW-100 to 1000 | Servo-hydraulic | 100–1000 kN | Rate-controlled acceptance |
| WAW-300C to 2000C | Servo-hydraulic, PC | 300–2000 kN | Bridges, nuclear components |
| WES-300C to 2000C | Compression | 300–2000 kN | Concrete, blocks |
| MMW-1A / MRS-10W | Friction and wear | — | Lubricants, coatings |
Three acceptance checks: verify force at 20/50/80% with a standard load cell; check alignment so a standard specimen breaks mid-gauge; run three identical specimens and look at scatter.
Specimen. Proportional (L₀ = 5.65√S₀) or non-proportional specimens to GB/T 228.1; transition radius R ≥ 5 mm; Ra ≤ 1.6 µm with work-hardened layers removed.
Measurement. Width and thickness at three positions within the gauge length, use the minimum for S₀; below 1 mm use optical or 0.001 mm micrometers.
Loading. 5–30 MPa/s in the elastic range, 0.00025/s strain rate at yield per method A, up to 0.0067/s in hardening; log at 100 Hz or more to catch yield serrations.
Evaluation. ReH is the first peak, ReL the lowest point, Rm the maximum force over S₀, A from the final gauge length (offset method), Z from the minimum fracture diameter.
Quality control. Daily check with a reference specimen, monthly force calibration with a class 0.3 proving instrument, half-yearly extensometer calibration, 23 ± 5 °C.