HOTHMAS-D5/10/30/50SZA Vickers Hardness Tester
Vickers Hardness Tester
- 测量分析系统HMAS‑硬度测量分析系统
- 光学成像系统维氏硬度大三通光学成像系统
HV-20Z · 2026-11-17 · +86 21 5748 2007
Vickers Hardness Tester
By submitting you agree to our privacy policy.
HV-20Z自动转塔维氏硬度计是本公司推出的第二代光机电一体化的高新技术产品,该机器造型新颖,具有良好的可靠性,可操作性和直观性,是采用精密机械技术和光电技术的新型维氏和努普硬度测试仪器.
性能特点:
1、自动加卸荷试验力机构,试验力保持时间可在0~99秒间任意选择
2、采用计算机软件编程,可进行维氏和努氏标尺间的转化
3、稳定的光学测量系统,能调节测量光源的强弱
4、面板显示屏直接显示硬度值,使用方便且测量精度高
测量范围:微小、薄形、表面渗镀层试件的显微硬度和测定玻璃、陶瓷、玛瑙、人造宝石等较脆而又硬材料
技术参数:
产品型号
HV-20Z
八档力(Kgf)
2、3、5、8、10、12、15、20
硬度值显示范围
0.001-9999.9HV
硬度值显示方式
主机电子小屏幕
塔台控制方式
自动控制
试验力加载
自动(加卸/保持/卸载)
试验力加载速度
0.2mm/s
符合标准(精度)
GB/T4340.2国家标准、JJG151检定规程;
最小检测单位
主机0.5μm
检测精度
机械0.1μm
测微目镜移动方式
0.4螺距螺杆
压痕测量长度
机械0.0-670μm
测量数据采集方式
主机手动采集
测量数据计算方式
主机自动计算
测微目镜倍率
主机10X (机械目镜)
物镜倍率
10X(观察)、20X(测量)
10X(观察、测量)
总放大倍率
100X(观察)、200X(测量)
100X(观察、测量)
硬度值换算
HV、HK、HBW、HRA、HRB、HRC、HRD、HRF、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T
打印机
主机无
测试储存组数
主机无
机身工艺
机身稳固
试验力读取
旋扭转换,自动读取
HV-20Z Vickers Hardness Tester supplied by CHWES. 21 key specifications available on request.
| 八档力(Kgf) | 2、3、5、8、10、12、15、20 |
|---|---|
| 硬度值显示范围 | 0.001-9999.9HV |
| 硬度值显示方式 | 主机电子小屏幕 |
| 塔台控制方式 | 自动控制 |
| 试验力加载 | 自动(加卸/保持/卸载) |
| 试验力加载速度 | 0.2mm/s |
| 符合标准(精度) | GB/T4340.2国家标准、JJG151检定规程; |
| 最小检测单位 | 主机0.5μm |
| 检测精度 | 机械0.1μm |
| 测微目镜移动方式 | 0.4螺距螺杆 |
| 压痕测量长度 | 机械0.0-670μm |
| 测量数据采集方式 | 主机手动采集 |
| 测量数据计算方式 | 主机自动计算 |
| 测微目镜倍率 | 主机10X (机械目镜) |
| 物镜倍率 | 10X(观察)、20X(测量) / 10X(观察、测量) |
| 总放大倍率 | 100X(观察)、200X(测量) / 100X(观察、测量) |
| 硬度值换算 | HV、HK、HBW、HRA、HRB、HRC、HRD、HRF、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T |
| 打印机 | 主机无 |
| 测试储存组数 | 主机无 |
| 机身工艺 | 机身稳固 |
| 试验力读取 | 旋扭转换,自动读取 |
* Generated by rule engine over the product database; for pre-selection only.
Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.
Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.
1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.
2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.
3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.
4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.
5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.
| Standard | Title | Scope |
|---|---|---|
| GB/T 4340.1-2009 | Vickers hardness test — test method | Vickers |
| GB/T 230.1-2018 | Rockwell hardness test | Rockwell |
| GB/T 231.1-2018 | Brinell hardness test | Brinell |
| ISO 6507-1 | Vickers hardness test | Export |
| ASTM E92 | Vickers hardness of metallic materials | Americas |
| GB/T 17394.1-2014 | Leeb hardness test | Portable |
Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.
1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.
2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.
3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.
4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.
5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.
6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.
| Model | Principle | Range | Typical use |
|---|---|---|---|
| HRC-150SMJ | Rockwell, motorised digital | HRA/HRB/HRC | Batch sampling in heat treatment |
| HRC-150SM / HRC-150M | Rockwell | HRA/HRB/HRC | Incoming and in-process checks |
| HRC-45M | Superficial Rockwell | 15N/30N/45N | Sheet, plating, case layers |
| HRS-150M / XHRS-150M | Digital Rockwell | HRA/HRB/HRC | Lines needing data upload |
| HBRVS-187.5 | Brinell-Vickers-Rockwell | HBW/HRA/HRB/HRC/HV | Mixed low-volume production |
Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.
Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.
Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.
Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.
Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.
Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.