HV-1000Z Micro Vickers Hardness Tester

Micro Vickers Hardness Tester

ModelHV-1000Z
  • 型号HV-1000Z
  • 转塔方式自动转塔
  • 加载机构砝码加载
  • 变荷装置机构齿轮垂直加载

By submitting you agree to our privacy policy.

01

Overview

HV-1000Z自动转塔显微硬度计是光机电一体化的高新技术产品,该机器造型新颖,具有良好的可靠性,可操作性和直观性,是采用精密机械技术和光电技术的新型显微维氏和努普硬度测试仪器。该机采用计算机软件编程,光学测量系统。显微硬度计适应于测量薄材料及微小零件的硬度,如钟表、仪器、仪表中的零件,及表面镀层、渗碳层、氮化层的硬度、厚度等等。是检验产品质量、制定合理的加工工艺的重要手段,特别是将成为金属学、金相学,即材料科学方面常用的试验方法之一。
性能特点:
1、硬度值显示功能:改变了传统的人工测量后自己查表出结果的计算方式、此方式较为烦琐,而本机改
为机器上测量只需输入测量压痕长度机器能自动出结果。方便、快捷、直观、为节省客户操作时间。
2、本机具备自动换力功能: 本机能根据客户需要选择力值大下自动读取实验力,实验力不必手动输入.直接旋转变荷手轮装置,即可自动读取实验力.
3、本机具备双显功能:本机采用LCD显示屏,同时显示两种硬度结果。通过操作控制键可选择硬度标尺HV或HK同时设定HRA、HRB、HRC、HB、等多种硬度换算结果。
4、自动转塔:自动切换物镜与压头
产品特点:
1.试验力小,对薄形样品或涂层均可测试;
2.压痕小,可认为无损检测,同时可在极小范围内进行多点测试;
3.全新浮点计算方法,使测试结果与理论结果更加接近一致;
4.全新大三通光路系统,接近100%光吸收;
5.物镜(压头)-基板-光学系统-照明四者一体化结构设计,几乎做到了100%精美光学系统;
6.主机硬件及软件采用预留端口设置,部分功能升级只需轻松拨码即可实现,使后续升级服务更加简便;
7.采用高端的光学成像技术,图像压痕清晰;
8.精确的360度塔台等分技术,让塔台定位更加正确;
9.可调的加卸载系统,让操作人员可轻松的完成多次测试;
10.可0-100%无级调节的照明系统,减轻了操作人员的视觉疲劳,同时自动控制的照明系统还可完成自动关闭与启动;
11.高级存储系统可以随时记忆测试结果,避免断电带来的数据丢失;
12.高精度的升降轴让机器运行更加平稳舒适;
13.稳定的机械结构设计,使机器的使用寿命更长;
技术参数:
型号: HV-1000Z
转塔方式: 自动转塔
加载机构: 砝码加载
变荷装置机构: 齿轮垂直加载
升降机构: 精密梯形丝杆
硬度值显示方式: LCD 屏
试验力: (8 级)N: 0.098N、0.245N、0.490N、0.981N、1.961N、2.942N、4.903N、9.807N;(8
级)gf: 10gf、25gf、50gf、100gf、200gf、300gf、500gf、1000gf;(8 级)标尺:
HV0.1、HV0.25、HV0.5、HV1、HV2、HV3、HV5、HV10
转换标尺:
HV、HK、HBW、HRA、HRB、HRC、HRD、HRF、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T
试验力加载: 全自动(加载 / 保荷 / 卸载)
执行国家标准: GB/T4340 国家标准,ISO6507 质量认证,ASTM 标准
X-Y 移动平台: 试台尺寸:100*100mm,试台移动范围25*25mm,机械读数0.01mm
理论硬度测量范围: 8-3000HV
目镜倍率: 10X(读数目镜)
物镜倍率: 10X(观察)、40X(测量)
总放大倍数: 100X(观察)、400X(测量)
读数方式: 毂轮读数
计算方式: 自动计算
最小检测单位: 0.25μm
试验力保荷时间: 0-99 秒,最小变动量 1 秒
试件最大高度: 70mm
压头中心到内壁距离: 110mm
机身工艺: 铸铝机身
电源电压: AC 220V/50Hz
外形尺寸: 220*450*460mm(长*宽*高)
净重: 25.0kg
毛重: 40.0kg

HV-1000Z Micro Vickers Hardness Tester supplied by CHWES. 28 key specifications available on request.

02

Specifications

型号HV-1000Z
转塔方式自动转塔
加载机构砝码加载
变荷装置机构齿轮垂直加载
升降机构精密梯形丝杆
硬度值显示方式LCD 屏
试验力(8 级)N: 0.098N、0.245N、0.490N、0.981N、1.961N、2.942N、4.903N、9.807N;(8
级)gf10gf、25gf、50gf、100gf、200gf、300gf、500gf、1000gf
(8 级)标尺HV0.;HV0.;HV0.;HV;HV;HV;HV;HV10
转换标尺HV、HK、HBW、HRA、HRB、HRC、HRD、HRF、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T
试验力加载全自动(加载 / 保荷 / 卸载)
执行国家标准GB/T4340 国家标准,ISO6507 质量认证,ASTM 标准
X-Y 移动平台试台尺寸:100*100mm,试台移动范围25*25mm,机械读数0.01mm
理论硬度测量范围8-3000HV
目镜倍率10X(读数目镜)
物镜倍率10X(观察)、40X(测量)
总放大倍数100X(观察)、400X(测量)
读数方式毂轮读数
计算方式自动计算
最小检测单位0.25μm
试验力保荷时间0-99 秒,最小变动量 1 秒
试件最大高度70mm
压头中心到内壁距离110mm
机身工艺铸铝机身
电源电压AC 220V/50Hz
外形尺寸220*450*460mm(长*宽*高)
净重25.0kg
毛重40.0kg

* Generated by rule engine over the product database; for pre-selection only.

03

Working principle

Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

  • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
  • Rockwell C 150 kgf: fast batch checking of hardened parts.
  • Brinell: castings, annealed and coarse-grain materials.
  • Leeb: portable rebound testing on large parts.
04

Process animation

  1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
  2. Mount and align: place the specimen, position the indenter over the test point.
  3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
  4. Load: apply force at the set rate, dwell 10–15 s.
  5. Measure: read diagonals or depth, compute HV/HRC.
  6. Gradient: step along depth and plot hardness versus distance.
0102030405
05

Calculation & formulas

1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

06

Standards

StandardTitleScope
GB/T 4340.1-2009Vickers hardness test — test methodVickers
GB/T 230.1-2018Rockwell hardness testRockwell
GB/T 231.1-2018Brinell hardness testBrinell
ISO 6507-1Vickers hardness testExport
ASTM E92Vickers hardness of metallic materialsAmericas
GB/T 17394.1-2014Leeb hardness testPortable

Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

07

Selection guide

1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

ModelPrincipleRangeTypical use
HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

08

Test method

Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

09

Industry applications

  • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
  • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
  • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
  • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
  • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
  • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
  • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
  • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0CompareProduct comparison