HMAS-UHT1700CM High-temperature Hardness Tester

High-temperature Hardness Tester

ModellHMAS-UHT1700CM
  • 使用温度范围400℃~1600℃
  • 炉腔温度范围≤1700℃
  • 温控精度≤±0.3℃
  • 温度场梯度误差≤±5℃

By submitting you agree to our privacy policy.

01

Überblick

HMAS-UHT1700CM用于400℃~1600℃材料性能研究,结合高温光学观察与力—时间记录。
以下为厂家原站标称参数。原文载荷单位kg保留,力值单位及可选项需在技术协议中确认;显示分辨率不等于测量准确度。
HMAS-UHT1700CM用于400℃~1600℃材料性能研究,结合高温光学观察与力—时间记录。
标配10X物镜,可选配20X物镜。完整参数表保留原站的标准配置与选配条件,载荷单位“kg”按原站记录,订购时需确认力值单位与校准范围。
测试温度范围、炉腔温度、压针预热温度及换样系统极限温度分别列示;各模块的极限值不能替代整机测试温度。
用于高温维氏硬度与压痕形貌分析。断裂韧性等派生量需选择适合材料与裂纹形态的评价方法,不能仅由产品配置认定方法有效。
全温场的含义是:加热炉、压针、物镜、加载机构与换样机构处在同一个温度场里。试样从装炉到压痕观察完成都不离开炉腔,不需要“加热—取出—冷却—再测量”,因此氧化、脱碳与组织转变不会被误读成材料本身的温度响应。
硬度形成链:压针在设定力值下压入试样表面并保荷,卸载后由物镜在同一温度场直接观察压痕,测量对角线 d,按 HV = 0.1891·F/d² 计算维氏硬度(F 单位 N,d 单位 mm)。力—时间原始曲线与压痕图像同时存档,用于复核与追溯。
温度链:4*U型二硅化钼 加热,B型 测温,温控精度 ≤±0.3℃,温场梯度 ≤±5℃,升温速率 1–40℃/min。炉腔显示温度、试样附近温度与压针预热温度分别记录;炉腔上限 1700℃ 是炉体能力,不等于可测温度 1600℃。
光学与运动链:10X 物镜(选配 20X),物镜工作温度 ≤1600℃,系统显示放大 1000X(选配 2000X),物镜分辨率 1.44 μm(选配 1.19 μm);多轴联动定位精度 ≤±1 μm,使“压入—观察—换点”在同一温度场里连续完成。分辨率是成像能力,不能当作测量准确度。
以 1 kgf(9.80665 N)载荷、压痕对角线 0.050 mm 为例:HV = 0.1891 × 9.80665 ÷ 0.050² ≈ 742。这是公式演示,不代表本机在该载荷下的实测值或不确定度。
hP P maxh max S = dP/dh hold (creep) 暂停动画重播force-depth力—位移曲线:加载段斜率、保荷段深度增长与卸载初始斜率分别对应弹性响应、时间相关变形与接触刚度。 动图为原理示意,曲线与数值非仪器实测数据。02 / CONFIGURATION仪器主要构成以下为本系列公开的模块构成,具体配置以技术协议为准;标注“选配”的项目不作为标准供货。

HMAS-UHT1700CM High-temperature Hardness Tester supplied by CHWES. 67 key specifications available on request.

02

Technische Daten

使用温度范围400℃~1600℃
炉腔温度范围≤1700℃
温控精度≤±0.3℃
温度场梯度误差≤±5℃
升温速率范围1℃~40℃/min
炉腔温场尺寸100*80*80mm
试样尺寸≤φ30*30mm
加热元件4*U型二硅化钼
控温热电偶B型
加载力值范围0.1~30kg
力值档位固定档位/自定义力值
固定档位力值标配61档
自定义力值输入力值
加载方式定力值/定速度
定力值加载精度≤1kg时±2%;>1kg时±0.5%
定力值加载分辨率0.01%FS
加载过程实时力值、时间数据
保荷时间≤72小时
传感器耐高温力值传感器
预热时长≤50小时
预热时间自定义,单位min或s
最高预热温度≤1600℃
物镜放大倍数10X物镜(选配20X物镜)
系统显示放大倍数1000X(选配2000X)
物镜分辨率1.44um,选配1.19um
物镜工作温度≤1600℃
单次持续工作时间≤50小时
更换方式手动,选配自动
更换时长≤50秒
系统极限温度≤2100℃
系统测试环境≤1700℃
联动轴数5轴(选配6~8轴)
运动控制精度≤±1um
运动控制速度≤5000um/s
运动控制分辨率≤0.1um
运动控制方式自动
X轴行程(横轴)250mm
Y-A轴行程(10X物镜)90mm
Y-B轴行程(20X物镜)90mm
Y-C轴行程(压针)90mm
Z轴行程12mm
Z-Y轴行程(样品升降轴)0~60mm手动/自动
最大流量13L/min
介质惰性气体
冷却时间≤5秒
气压0.8Mpa
冷却温度≤55℃
持续工作时间≤72小时
冷却组数4
冷却角90°
可修复次数≤20次
单次加载持续时间≤72小时
全尺寸1700型压针110mm*φ8(可选配110mm*φ6.35)
水氧指标≤1ppm
工位数1.0
尺寸2200*1420*2270mm
腔室尺寸1350*950*1400mm
箱体材质304不锈钢
箱体底板材质304不锈钢
额定制冷量1050W
制冷剂R134a
温度范围15~36℃
噪音≤63dB(A)
仪器外形尺寸2400*1500*2350mm(安置空间大于长3800*宽2000*高2800mm)
仪器重量1800kg(环境无振动)
气源99.999%高纯氩气等
电源220V(功率>6.5KW)

* Generated by rule engine over the product database; for pre-selection only.

03

Messprinzip

HMAS/IMAS full-temperature instruments bring loading, optics and temperature control to the hot end simultaneously:

  • Furnace: 4×U-shaped MoSi₂ elements, chamber to 1700 °C; type-B thermocouple with multi-segment PID holds ±0.3 °C, gradients within ±5 °C (100×80×80 mm) at 1–40 °C/min ramp.
  • Loading: 0.1–30 kg standard (1–150 kg optional), 61 fixed steps plus custom values, constant-force or constant-rate modes with full force-time logging; holds to 72 h for creep studies.
  • Hot optics: 10× (optionally 20×) objectives resolve 1.44 µm at 1600 °C for in-situ indentation and crack imaging.
  • Sample handling: same-temperature exchange within 50 s; glovebox with H₂O/O₂ below 1 ppm and inert or vacuum atmospheres prevent oxidation.

The IMAS indenters add instrumented loading (ISO 14577), deriving hot modulus and hardness from force–displacement curves by the Oliver-Pharr method.

04

Process animation

  1. Load and preheat: place the specimen (≤φ30×30 mm) in the chamber and preheat the indenter.
  2. Ramp and soak: heat at 1–40 °C/min to the setpoint under closed-loop control.
  3. In-situ focus: focus the 10×/20× objective on the target site free of oxide.
  4. Load and hold: constant-force or constant-rate loading with real-time logging (force–time, or force–displacement on IMAS) and holds from seconds to 72 h.
  5. Unload and measure: read the diagonals in the same field, or derive contact depth from the curve; exchange specimens in ≤50 s.
  6. Modelling: software produces hardness or modulus-versus-temperature curves and reports.
0102030405
05

Calculation & formulas

1. Vickers: HV = 1.8544·F/d² (F in kgf, mean diagonal d in mm); F = 1 kgf with d = 0.06 mm gives HV ≈ 515. Ceramics at 1600 °C typically need 1–5 kgf.

2. Loading accuracy: ±2% below 1 kg, ±0.5% above, 0.01% FS resolution; the force-time slope yields the loading rate.

3. Instrumented indentation (Oliver-Pharr): stiffness S = dP/dh from the top third of unload; hc = hmax − 0.75Pmax/S; Ac = 24.5hc²; H = Pmax/Ac; Er = (√π/2)S/√Ac, with E solved from the compliance relation.

4. Hot fracture toughness: KIC = 0.016(E/H)1/2F/c3/2; with E/H = 20, F = 10 kgf, c = 0.15 mm, KIC ≈ 4.1 MPa·m1/2.

5. Creep: fit the hold segment displacement for the strain rate ε̇ = dh/dt/hc to judge microstructural stability.

06

Normen

StandardTitleScope
GB/T 4340.1-2009Metallic materials — Vickers hardness test, Part 1Indentation measurement
ASTM E92-17Vickers and Knoop hardnessAcceptance testing
ASTM E384-17Microindentation hardnessMicro/small-force indents
ISO 14577-1:2015Instrumented indentation test, Part 1IMAS modulus/hardness
ISO 14577 seriesHigh-temperature indentation annex guidanceHot-stage traceability

Record temperature points, soak time, atmosphere, raw force-time data and in-situ images for research-grade traceability.

07

Auswahl

1. Temperature first: take process temperature plus 20% headroom. 600 °C class: HMAS-HT600/HT700CM; 800 °C: HT800/HT900CM; 1200 °C: HT1200/HT1300CM; 1400 °C: HT1500CM; 1600 °C: HMAS-UHT1700CM or IMAS-UHT1700.

2. Hardness only or full curve: HMAS for Vickers indents and morphology; IMAS for force-displacement curves, hot modulus and creep compliance to ISO 14577.

3. Atmosphere drives configuration: TiAl, refractory metals and coatings need inert gas or vacuum (O₂ ≤10 ppm) with a glovebox; heat-resistant steels and cast irons run on high-purity argon.

4. Load by material: 0.1–10 kg for ceramics and thin coatings, 1–30 kg standard for superalloys and hardmetals, up to 150 kg for castings and forgings.

5. Production or research: 50 s same-field sample exchange and multi-station for line sampling; in-situ imaging, programmable temperature steps and full raw-data export for research.

6. Facility: ≥3.8×2.0×2.8 m footprint, 99.999% argon, 220 V / ≥6.5 kW, floor vibration ≤VC-C.

Model rangeMax temperatureTypical useKey capability
HMAS-HT600 / HT700CM600–700 °CAl/Cu alloys, tempered steelVickers indent + in-chamber imaging
HMAS-HT800 / HT900CM800–900 °CHeat-resistant steel, cast iron, hardmetalLong soak, batch exchange
HMAS-HT1200 / HT1300CM1200–1300 °CNi superalloys, TBCInert atmosphere, coating cross-sections
HMAS-HT1500CM1500 °CRefractory alloys, ceramicsHigh vacuum, hot optics
HMAS-UHT1700CM / IMAS-UHT17001600–1700 °CUHTC, single crystal, nuclearExtreme chamber, in-situ curves
IMAS-HT700CM / HT900CM700–900 °CCreep and modulusISO 14577 force-displacement

What moves price and lead time: temperature ceiling, vacuum or glovebox, load range, in-situ imaging and thermal-conductivity ports, LIMS integration. Standard units ship in 45–60 days; 1600 °C and glovebox configurations need 90 days or more.

08

Prüfverfahren

Specimens: ≤φ30×30 mm, parallelism ≤0.02 mm, measuring face Ra ≤0.4 µm (ideally ≤0.1 µm); transfer refractories inside the glovebox to avoid moisture pickup.

Temperature: verify with the type-B couple near the specimen; soak 15–30 min per point until gradients are within ±5 °C before loading.

Indenter: manage diamond life (≤50 h), keep one indenter per campaign, spacing indentations 3–4 diagonals apart.

Data: ≥3 valid indents per temperature, full force-time curves (plus displacement on IMAS); discard and photograph anomalous unloads (oxidation, spalling).

Checks: verify the loading chain on a certified block at 25 °C; quarterly high-temperature consistency runs with a reference ceramic.

09

Industry applications

  • Aero-engine hot sections: hardness and modulus retention of single-crystal blades, powder discs and combustor liners at 800–1200 °C; hardness gradients across TBC ceramic and bond coats. Acceptance: HV spread of three indents ≤3%, temperature deviation ≤±3 °C.
  • Nuclear materials: pre/post-irradiation hot hardness of Zr-4/Zirlo cladding and 316L/690 alloys, creep compliance versus time; acceptance: drift ≤0.5 µm over 2 h at 400 °C.
  • Refractory metals and UHTCs: intrinsic hardness of W/Mo alloys, ZrB₂-SiC and HfC up to 1600 °C; vacuum ≤5×10⁻³ Pa, indents still measurable after 30 min soak.
  • Hardmetals and PM parts: sintering-window validation via hardness at 1000 °C versus cobalt content, replacing part of the high-temperature bend tests.
  • Automotive powertrain: softening curves of turbo-housing and manifold heat-resistant cast irons; correlation with 800 °C yield strength R² ≥0.85.
  • Coatings and cutting tools: high-temperature softening and coating-substrate failure temperature of TiAlN, AlCrN and DLC films; red hardness comparison.
  • Academia: in-situ mechanical data for transformation, creep and oxidation kinetics, with raw force-displacement-time export.
  • Third-party testing: round-robin hot-hardness comparisons and failure reproduction; chamber uniformity ≤±5 °C under a valid calibration.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0VergleichTechnischer Vergleich