MMAS-20 Polarizing Microscope (倒置偏光)

Polarizing Microscope · 倒置偏光

型番MMAS-20
  • 物镜无限远平场消色差物镜PLL10X/0.25,工作距离:5mm
  • 放大倍数100~1000X
  • 目镜筒倾斜45度,瞳距调节范围53-75mm
  • 照明系统6V30W卤素灯,亮度可调

By submitting you agree to our privacy policy.

01

製品概要

MMAS-20倒置偏光金相显微镜测量分析系统采用优良的无限远光学系统与模块化的功能设计理念,可以方便升级系统,实现偏光观察、暗场观察等功能。紧凑稳定的高刚性主体,充分体现了显微镜操作的防振要求。符合人机工程学要求的理想设计,使操作更方便舒适,空间更广阔。适用于金相组织及表面形态的显微观察,是金属学、矿物学、精密工程学研究的理想仪器。MMAS-20系统配备了研润自主研发的MMAS测量分析系统以及MOS高端光学系统。
一、技术特点:
1、观察系统:铰链式双目,45度倾斜,大视野平场广角目镜,视场范围直径22mm。
2、机械载物台:外形尺寸:242mmX200mm,移动范围30mmX30mm。圆形可旋转载物台板尺寸:最大外径Ф130mm,最小通光口径小于Ф20mm;圆形可旋转台板用于偏光观察时满足偏光镜检的要求。
3、照明系统:柯拉照明,12V/50W或12V/50W卤素灯可选。孔径光栏与视场光栏可通过拨盘进行孔径大小的调整。可选配360度调整偏振角的起偏器。可选明暗视场照明器。
4、选配的暗场观察系统:可选配暗场观察物镜与照明装置,有效消除有害光线。
5、选配件:
5.1分化目镜:10X(直径22mm),格值0.1mm/格;
5.2明暗场无限远长距消色差物镜:PLL5X/0.12(工作距离8.05)、PLL10X/0.25(工作距离7.86)、PLL20X/0.4(工作距离7.23)、PLL40X、PLL50X/0.7(工作距离1.75)、PLL60X/0.7(工作距离2.08)、PLL80X/0.8(工作距离1.25)、PLL100X/0.85(干式、工作距离0.4);
5.3选配明场物镜:5X、40X、60X、80X、100X(油)
5.4适配镜:0.5X、1X;
5.5数码摄像机;
二、技术参数:
目镜
大视野 WF10X(Φ22mm)
物镜
无限远平场消色差物镜PLL10X/0.25,工作距离:5mm
无限远平场消色差物镜PLL20X/0.4,工作距离:8.8mm
无限远平场消色差物镜PLL50X/0.7,工作距离:3.68mm
无限远平场消色差物镜PL L100X/0.85,工作距离:0.4mm
放大倍数
100~1000X
目镜筒
倾斜45度,瞳距调节范围53-75mm
照明系统
6V30W卤素灯,亮度可调
内置视场光栏、孔径光栏、拉板式起偏器,配置黄绿蓝滤色片及磨砂玻璃
调焦机构
粗微动同轴调焦, 微动格值:2μm,粗动松紧可调,带锁紧和限位装置
转换器
五孔(内向式滚珠内定位);
载物台
双层机械移动式(尺寸:242mmX200mm,移动范围:30mmX30mm)
圆形可旋转载物台板尺寸:最大外径Ф130mm,最小通光口径小于Ф20mm
外形尺寸
455*545*280
配备系统
主机+MMAS数据处理系统1套+MOS光学系统一套+电脑一套

MMAS-20 Polarizing Microscope (倒置偏光) supplied by CHWES. 9 key specifications available on request.

02

仕様

物镜无限远平场消色差物镜PLL10X/0.25,工作距离:5mm
放大倍数100~1000X
目镜筒倾斜45度,瞳距调节范围53-75mm
照明系统6V30W卤素灯,亮度可调
调焦机构粗微动同轴调焦, 微动格值:2μm,粗动松紧可调,带锁紧和限位装置
转换器五孔(内向式滚珠内定位);
载物台双层机械移动式(尺寸:242mmX200mm,移动范围:30mmX30mm)
外形尺寸455*545*280
配备系统主机+MMAS数据处理系统1套+MOS光学系统一套+电脑一套

* Generated by rule engine over the product database; for pre-selection only.

03

測定原理

The metallurgical microscope uses an infinity-corrected optical path with reflected Köhler illumination. Light passes the collector, field stop and aperture stop, is deflected by a semi-transparent mirror through the objective onto the specimen, and returns through the same objective to the eyepiece or camera.

  • Bright field for routine microstructure, inclusions and decarburised layers.
  • Dark field collects scattered light to reveal grain boundaries, cracks and non-metallic inclusions.
  • Polarised light identifies anisotropic phases, spheroidised structures and coating stress.
  • DIC converts tiny height differences into contrast, ideal for polished, unetched samples.

Objectives of 5× to 100× are combined with 10× eyepieces. Higher numerical aperture gives better resolution but shallower depth of field.

04

Process animation

  1. Sampling and preparation: sectioning, mounting, grinding, polishing, etching.
  2. Illumination and focus: select BF/DF/POL/DIC and focus.
  3. Image capture: trinocular port, 1× camera adapter, white balance.
  4. Scale calibration: calibrate µm per pixel with a stage micrometer.
  5. Measurement: grain size, case depth, coating thickness, inclusion rating.
0102030405
05

Calculation & formulas

1. System magnification: M = objective × eyepiece × adapter, e.g. 40× / 10× / 1× = 400×.

2. Resolution: d = 0.61λ/NA (λ≈550 nm). A 40× objective with NA 0.65 resolves 0.52 µm; an NA 0.95 dry objective reaches 0.35 µm.

3. Depth of field scales with λ/NA² — higher NA, shallower depth; use low NA for fracture surfaces.

4. Grain size (GB/T 6394): at 100×, grains N per 645 mm² field follow N = 2G−1; counting 128 grains gives G = log2128 + 1 = 8. Intercept method: mean intercept L̄ = line length ÷ intercepts, G = −6.6437 lg L̄ (mm, 100×).

5. Effective case depth: distance to 550 HV1, fitted from a micro-hardness traverse and averaged over three positions.

06

規格

StandardTitleScope
GB/T 13298-2015Metallic materials — examination of microstructureMicrostructure rating
GB/T 6394-2017Determination of average grain sizeGrain size
ASTM E3-11Guide for metallographic specimen preparationPreparation
ASTM E112Determining average grain sizeGrain size
ISO 643Steels — micrographic determination of grain sizeGrain size

Export projects often require dual GB and ASTM reports; the software ships both rating charts.

07

選定ガイド

1. Surface or cross-section: stereo microscopes (HX-ZG7, XSZ) for fracture surfaces, solder joints and coatings; upright or inverted metallurgical microscopes (HX-4, HX-G series) for microstructure, case depth and inclusions.

2. Upright or inverted: upright for small specimens that are flipped often; inverted (HX-G3A/G4C/G5A) for large, heavy parts such as gears, shafts and tube sections that go straight onto the stage without re-mounting.

3. Optics set the ceiling: plan achromats cover routine rating; semi-apochromats or apochromats with a research stand (HX-G5A) are needed for 1000× precipitates and brightfield/darkfield/polarised switching.

4. Three levels of digitalisation: a 5 MP camera for images; camera plus analysis software (grain size, case depth, inclusions, porosity) for automatic rating and reports; motorised stage with scanning and stitching for unattended batches.

5. Do not forget accessories: polariser, darkfield, DIC, and a microhardness interface.

6. Room: an anti-vibration bench at 20±3 °C for research stands; keep preparation and microscopy rooms separate to avoid abrasive dust.

SeriesTypeTypical taskRecommended setup
HX-4A / HX-4BUpright metallurgicalRoutine structure, case depth5×/10×/40× + 5 MP camera
HX-G2A / G2BInvertedBatch samples, no re-mountingBrightfield + simple polariser
HX-G3ATrinocular invertedCase depth, rating, reportsCamera + analysis software
HX-G4C / G5AResearch invertedDarkfield/polarised/DICSemi-apochromat + motorised stage
HX-ZG7 / XSZ-146StereoFracture, solder, low-mag locatingZoom + ring light

Common misconceptions: higher magnification is not better (numerical aperture limits resolution, 100× dry is the practical ceiling); ignoring stage travel so large samples do not fit; buying the stand without software and still rating by eye, which kills repeatability.

08

試験方法

Preparation. Section perpendicular to the feature of interest. Keep hot-mounting below 150 °C for aluminium and quenched parts, or use cold mounting. Grind 320→600→800→1200, removing previous scratches at each step; polish with 3 µm then 1 µm diamond. Etchants: 4% nital for carbon steel (3–8 s), aqua regia or electrolytic for stainless, Keller for aluminium.

Examination. Locate a representative field at 5×/10×, then switch to higher power. Rate grain size to GB/T 6394 by comparison or intercept. Measure case depth at 500× with an ocular scale or calibrated software, averaging five readings.

Calibration. Verify µm/pixel daily with a stage micrometer, check against a certified specimen quarterly, record three fields per sample and archive images with scale bars.

Pitfalls. Over-etching widens boundaries and fakes decarburisation; residual scratches can be mistaken for cracks; rounded mounting edges inflate case depth. Keep an unetched specimen for coating and crack review.

09

Industry applications

  • Steel and heat treatment: decarburised depth, carburised/nitrided case depth, grain size (GB/T 6394), non-metallic inclusions (GB/T 10561), banding and Widmanstätten rating.
  • Non-ferrous metals: aluminium grain and recrystallisation, alpha/beta ratio in brass, twinning and corrosion morphology in magnesium.
  • Welding and brazing: penetration, HAZ width, porosity and cracks, intermetallic thickness at dissimilar joints.
  • Additive manufacturing: porosity, lack-of-fusion defects, melt-pool morphology in SLM parts, porosity repeatability within 0.2%.
  • Bearings and gears: martensite rating, retained austenite, carbide network and banding, grinding burn and white layer.
  • Electronics: IMC thickness, plating cross-sections, PCB micro-sections, gold wire ball bonds (stereo plus metallurgical).
  • Powders and ceramics: particle morphology and size, sintered porosity, coating cross-section thickness.
  • Failure analysis: fracture surface macro and micro morphology, corrosion products, crack path and origin, with stereo microscopy for low-magnification locating.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0比較仕様比較