MIC20 Hardness Tester

Hardness Tester

型番MIC20
  • 电源供应交流(100V-240V)或镍氢电池;内部数据记录,约可记录5000个系列测量值;根据不同测试材料可进行快速简单的校准,校准数据能够被存储并重新调出;无方向性测量,无需输入任何校正因素

By submitting you agree to our privacy policy.

01

製品概要

一、MIC20组合式硬度计产品简介:
MIC20组合式硬度计(超声波/里氏两用硬度计)将UCI法(超声接触阻抗法)和回弹硬度检测法合为一体。UCI法可用于检测具有复杂形状的质地细密的材料,回弹法用于检测大型粗晶粒锻件和铸件。UCI法在施加试验负载后,通过测量维氏金刚石在材料后面留下的压痕尺寸,从而确定材料的硬度。在回弹法中,一个撞击体在弹力作用下,被推到检测面上。撞击速度和回弹速度都是通过非接触模式测得的,通过这两个数值测得硬度数值。
二、MIC20组合式硬度计产品特点:
1、结合了UCI法(ASTM A1038)的准静态硬度测试与根据回弹法(ASTM A956)的动态硬度测试的硬度计
2、UCI探头适用的硬度测试为纹理精细、拥有复杂形状或经过热处理的表面
3、回弹冲击设备用于纹理粗糙的大型元件以及锻造及铸造的材料
4、测试结果在HV、HB、HRC、HRB、HS、HL和N/mm2标准间自动换算
5、通过按键和/或内置触摸屏进行操作,方便的字母数字数据输入
6、电源供应:交流(100V-240V)或镍氢电池
7、内部数据记录,约可记录5000个系列测量值
8、根据不同测试材料可进行快速简单的校准,校准数据能够被存储并重新调出
9、无方向性测量,无需输入任何校正因素
10、大型彩色TFT屏幕,显示所有测量相关信息,如平均值、单个值或统计数字
11、排列清晰的数据存储,能简单而有序地进行测量结果存储。系列测量值能够被调出并进行编辑
三、MIC20组合式硬度计UCI测试:
1、组装好的机械设备
2、焊接的受热影响区域(如:管道)
3、热处理表面(如:齿面)
4、镀层(如:凹版滚筒)回弹硬度测试:
5、钢制或铸铝合金的机械零件或电机组
6、表面卷曲、纹理粗糙的坚实元件
7、生产中的大型系列零件
8、重型锻造
四、MIC20组合式硬度计检测方法:
超声波UCI法:在负载下对维氏压痕进行评估得到硬度值
里氏回弹法:动态检测法,符合ASTM标准A956规格
五、MIC20组合式硬度计探头:
超声波UCI探头
手动探头:
10N(1kgf):标准MIC201-A、短探头MIC201-AS、长探头MIC201-AL
50N(5kgf):标准MIC205-A、短探头MIC205-AS、长探头MIC205-AL
98N(10kgf):标准MIC
2010A
电动探头
8.6N(0.9kgf):MIC211-A
3N(0.3kgf):MIC2103-A
1N(0.1kgf):MIC2101-A
里氏回弹探头
DynaD、Dyna G、DynaE
六、MIC20组合式硬度计检测范围:
1、检测范围/换算(超声波UCI):20~1740HV/76~618HS/41~105HRB/20.3~68.0HRC/255~2180N/mm2(仅用98N/10kgf手持探头)
2、测量范围/换算(里氏回弹):150~1000HL/750~1000HV/75~700HB/30~100HS/35~100HRB/19~70HRC/250~2200N/mm2(取决于材料类型和冲击设备)

MIC20 Hardness Tester supplied by CHWES. 1 key specifications available on request.

02

仕様

电源供应交流(100V-240V)或镍氢电池;内部数据记录,约可记录5000个系列测量值;根据不同测试材料可进行快速简单的校准,校准数据能够被存储并重新调出;无方向性测量,无需输入任何校正因素

* Generated by rule engine over the product database; for pre-selection only.

03

測定原理

Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

  • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
  • Rockwell C 150 kgf: fast batch checking of hardened parts.
  • Brinell: castings, annealed and coarse-grain materials.
  • Leeb: portable rebound testing on large parts.
04

Process animation

  1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
  2. Mount and align: place the specimen, position the indenter over the test point.
  3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
  4. Load: apply force at the set rate, dwell 10–15 s.
  5. Measure: read diagonals or depth, compute HV/HRC.
  6. Gradient: step along depth and plot hardness versus distance.
0102030405
05

Calculation & formulas

1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

06

規格

StandardTitleScope
GB/T 4340.1-2009Vickers hardness test — test methodVickers
GB/T 230.1-2018Rockwell hardness testRockwell
GB/T 231.1-2018Brinell hardness testBrinell
ISO 6507-1Vickers hardness testExport
ASTM E92Vickers hardness of metallic materialsAmericas
GB/T 17394.1-2014Leeb hardness testPortable

Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

07

選定ガイド

1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

ModelPrincipleRangeTypical use
HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

08

試験方法

Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

09

Industry applications

  • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
  • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
  • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
  • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
  • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
  • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
  • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
  • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0比較仕様比較