HVS-1000M Micro Vickers Hardness Tester

Micro Vickers Hardness Tester

型番HVS-1000M
  • 型号HVS - 1000M
  • 转塔方式手动转塔
  • 加载机构砝码加载
  • 变荷装置机构齿轮垂直加载

By submitting you agree to our privacy policy.

01

製品概要

HVS-1000M系列触摸屏显微硬度计为自主开发升级产品,采用5.6寸真彩色触摸屏、源于奥迪多媒体操控原理设计而成,操作更加直观方便。它除了测量维氏硬度以外,还可以另配努氏(Knoop)压头进行努氏硬度测量。努氏(Knoop)硬度测试
,对一些薄样品、窄样品以及一些要求在较小范围内进行多密点测量的样品测试有独到之处。另对于一些脆性超硬样品的测试也很有优势。还可以搭配HMAS专业显微硬度测量分析软件,拓展仪器功能,提高仪器测量精度和工作效率。
产品特点:
1、采用5.6寸真彩色触摸屏
2、配备数字式编码器直接采集数据,高精度测量。
3、高分辨率的成像系统,可高清晰的观察显示出压痕。
4、物镜(压头)-塔台基板-光学系统-照明四者一体化结构设计,几乎做到了100%精美光学系统;
技术参数 :
型号: HVS - 1000M
转塔方式: 手动转塔
加载机构: 砝码加载
变荷装置机构: 齿轮垂直加载
升降机构: 精密梯形丝杆
硬度值显示方式: 触摸屏
试验力:
(8级)N:0.098N、0.245N、0.490N、0.981N、1.961N、2.942N、4.903N、9.807N;(8级)gf:10gf、25gf、50gf、100gf、200gf、300gf、500gf、1000gf;(8级)标尺:HV0.01、HV0.025、HV0.05、HV0.1、HV0.2、HV0.3、HV0.5、HV1
转换标尺:
HV、HK、HBW、HRA、HRB、HRC、HRD、HRF、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T
试验力加载: 全自动(加载 / 保荷 / 卸载)
执行国家标准: GB/T4340 国家标准,ISO6507 质量认证,ASTM 标准
X - Y 移动平台: 试台尺寸:100*100mm,试台移动范围25*25mm,机械读数0.01mm
理论硬度测量范围: 8-3000HV
目镜倍率: 10X(数显目镜)
物镜倍率: 10X、40X(测量)
总放大倍数: 100X、400X(测量)
读数方式: 编码器采集读数
计算方式: 自动计算
最小检测单位: 0.06μm(100X),0.0158μm(400X)
试验力保荷时间: 0 - 60 秒,最小变动量 1 秒
试件最大高度: 70mm
压头中心到内壁距离: 110mm
机身工艺: 铸铝机身
电源电压: AC 220V/50Hz
外形尺寸: 220*450*460mm(长*宽*高)
净重: 25.0kg
毛重: 40.0kg
显微触摸屏硬度计软体图片:

HVS-1000M Micro Vickers Hardness Tester supplied by CHWES. 28 key specifications available on request.

02

仕様

型号HVS - 1000M
转塔方式手动转塔
加载机构砝码加载
变荷装置机构齿轮垂直加载
升降机构精密梯形丝杆
硬度值显示方式触摸屏
(8级)N0.098N、0.245N、0.490N、0.981N、1.961N、2.942N、4.903N、9.807N
(8级)gf10gf、25gf、50gf、100gf、200gf、300gf、500gf、1000gf
(8级)标尺HV0.;HV0.0;HV0.;HV0.;HV0.;HV0.;HV0.;HV1
转换标尺HV、HK、HBW、HRA、HRB、HRC、HRD、HRF、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T
试验力加载全自动(加载 / 保荷 / 卸载)
执行国家标准GB/T4340 国家标准,ISO6507 质量认证,ASTM 标准
X - Y 移动平台试台尺寸:100*100mm,试台移动范围25*25mm,机械读数0.01mm
理论硬度测量范围8-3000HV
目镜倍率10X(数显目镜)
物镜倍率10X、40X(测量)
总放大倍数100X、400X(测量)
读数方式编码器采集读数
计算方式自动计算
最小检测单位0.06μm(100X),0.0158μm(400X)
试验力保荷时间0 - 60 秒,最小变动量 1 秒
试件最大高度70mm
压头中心到内壁距离110mm
机身工艺铸铝机身
电源电压AC 220V/50Hz
外形尺寸220*450*460mm(长*宽*高)
净重25.0kg
毛重40.0kg

* Generated by rule engine over the product database; for pre-selection only.

03

測定原理

Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

  • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
  • Rockwell C 150 kgf: fast batch checking of hardened parts.
  • Brinell: castings, annealed and coarse-grain materials.
  • Leeb: portable rebound testing on large parts.
04

Process animation

  1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
  2. Mount and align: place the specimen, position the indenter over the test point.
  3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
  4. Load: apply force at the set rate, dwell 10–15 s.
  5. Measure: read diagonals or depth, compute HV/HRC.
  6. Gradient: step along depth and plot hardness versus distance.
0102030405
05

Calculation & formulas

1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

06

規格

StandardTitleScope
GB/T 4340.1-2009Vickers hardness test — test methodVickers
GB/T 230.1-2018Rockwell hardness testRockwell
GB/T 231.1-2018Brinell hardness testBrinell
ISO 6507-1Vickers hardness testExport
ASTM E92Vickers hardness of metallic materialsAmericas
GB/T 17394.1-2014Leeb hardness testPortable

Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

07

選定ガイド

1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

ModelPrincipleRangeTypical use
HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

08

試験方法

Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

09

Industry applications

  • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
  • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
  • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
  • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
  • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
  • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
  • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
  • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0比較仕様比較