HMAS-D5 Vickers Hardness Tester

Vickers Hardness Tester

型番HMAS-D5
  • 测量分析系统维氏硬度测量分析系统
  • 光学成像系统维氏硬度大三通光学成像系统
  • 主机屏幕LCD 屏
  • 转塔方式手动转塔

By submitting you agree to our privacy policy.

01

製品概要

HMAS-D5/10/20/30/50维氏硬度测量分析系统是本公司推出的第六代光机电一体化的高新技术产品,该机器造型新颖,具有良好的可靠性,可操作性和直观性,是采用精密机械技术、光电技术、图形图像处理技术和材料硬度分析软件的新型维氏和努普硬度测试仪器。
性能特点:
1、外观新颖,通过软件执行操作,进一步实现测量的智能化
2、设备摈弃传统繁琐测量步骤,测量方法更简便
3、设备自带打印功能,可将相关测量参数打印并保存
4、设备能对被测材料进行拍摄并能对其组织进行分析和读取
5、可调节测量光源强弱,可预置试验力保持时间、并能切换维氏和努氏试验方法
使用范围:
热处理、碳化、淬火硬化层,表面覆层,钢,有色金属和微小及薄形零件等. 选配努氏压头可测定微小、薄形试件、表面渗镀层等试件的显微硬度和玻璃、陶瓷、玛瑙、人造宝石等较脆而又硬的材料。
技术参数:
型号
HMAS‑D5
测量分析系统
维氏硬度测量分析系统
光学成像系统
维氏硬度大三通光学成像系统
主机屏幕
LCD 屏
转塔方式
手动转塔
变荷装置机构
砝码加载
升降机构
精密梯形丝杆
HMAS‑D5试验力
(5Kg):0.2kgf、0.3kgf、0.5kgf、1kgf、3kgf、5kgf;
转换标尺
HV、HK、HBW、HRA、HRB、HRC、HRD、HRF、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T
试验力加载
全自动(加载 / 保荷 / 卸载)
执行国家标准
GB/T4340 国家标准,ISO6507 质量认证,ASTM 标准
理论硬度测量范围
8 - 6000HV(可选更大范围)
硬度值测量方式
(双系统测量) 主机单独测量 / 电脑软件测量分析
目镜倍率
10X
HMAS‑D5/10物镜倍率
(5Kg、10Kg):10X(观察)20X(测量),
HMAS‑D30/50物镜倍率
(30Kg、50Kg):10X(观察、测量)
HMAS‑D5/10总放大倍数
(5Kg、10Kg):100X(观察)200X(测量)
HMAS‑D30/50总放大倍数
(30Kg、50Kg):100X(观察、测量), 电脑大约: 10X (375x)、20X (750x)
主机最小检测单位
1μm(10X 物镜), 0.5μm(20X 物镜)
试验力保荷时间
0 - 99 秒,最小变动量 1 秒
试件最大高度
235mm
压头中心到内壁距离
130mm
外形尺寸
220*570*680mm(长*宽*高)
净重
54.0kg
毛重
72.0kg

HMAS-D5 Vickers Hardness Tester supplied by CHWES. 24 key specifications available on request.

02

仕様

测量分析系统维氏硬度测量分析系统
光学成像系统维氏硬度大三通光学成像系统
主机屏幕LCD 屏
转塔方式手动转塔
变荷装置机构砝码加载
升降机构精密梯形丝杆
HMAS‑D5试验力(5Kg):0.2kgf、0.3kgf、0.5kgf、1kgf、3kgf、5kgf;
转换标尺HV、HK、HBW、HRA、HRB、HRC、HRD、HRF、HR15N、HR30N、HR45N、HR15T、HR30T、HR45T
试验力加载全自动(加载 / 保荷 / 卸载)
执行国家标准GB/T4340 国家标准,ISO6507 质量认证,ASTM 标准
理论硬度测量范围8 - 6000HV(可选更大范围)
硬度值测量方式(双系统测量) 主机单独测量 / 电脑软件测量分析
目镜倍率10X
HMAS‑D5/10物镜倍率(5Kg、10Kg):10X(观察)20X(测量)
HMAS‑D30/50物镜倍率(30Kg、50Kg):10X(观察、测量)
HMAS‑D5/10总放大倍数(5Kg、10Kg):100X(观察)200X(测量)
HMAS‑D30/50总放大倍数(30Kg、50Kg):100X(观察、测量), 电脑大约: 10X (375x)、20X (750x)
主机最小检测单位1μm(10X 物镜), 0.5μm(20X 物镜)
试验力保荷时间0 - 99 秒,最小变动量 1 秒
试件最大高度235mm
压头中心到内壁距离130mm
外形尺寸220*570*680mm(长*宽*高)
净重54.0kg
毛重72.0kg

* Generated by rule engine over the product database; for pre-selection only.

03

測定原理

Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

  • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
  • Rockwell C 150 kgf: fast batch checking of hardened parts.
  • Brinell: castings, annealed and coarse-grain materials.
  • Leeb: portable rebound testing on large parts.
04

Process animation

  1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
  2. Mount and align: place the specimen, position the indenter over the test point.
  3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
  4. Load: apply force at the set rate, dwell 10–15 s.
  5. Measure: read diagonals or depth, compute HV/HRC.
  6. Gradient: step along depth and plot hardness versus distance.
0102030405
05

Calculation & formulas

1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

06

規格

StandardTitleScope
GB/T 4340.1-2009Vickers hardness test — test methodVickers
GB/T 230.1-2018Rockwell hardness testRockwell
GB/T 231.1-2018Brinell hardness testBrinell
ISO 6507-1Vickers hardness testExport
ASTM E92Vickers hardness of metallic materialsAmericas
GB/T 17394.1-2014Leeb hardness testPortable

Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

07

選定ガイド

1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

ModelPrincipleRangeTypical use
HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

08

試験方法

Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

09

Industry applications

  • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
  • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
  • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
  • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
  • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
  • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
  • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
  • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
10

Price and lead time for this model

By submitting you agree to our privacy policy.

⇄0比較仕様比較