HBRVW-187.5 Hardness Tester

Hardness Tester

型番HBRVW-187.5

    By submitting you agree to our privacy policy.

    01

    製品概要

    HBRVW-187.5智能布洛维硬度计为研润自主研发生产第三代高端产品,采用windows系统平板电脑控制。该机采用VB语言编程,微机模式操作,与闭环式高精度传感器精美的融合、避免了砝码式的繁琐,大大提高了工作效率及力值的准确性,是机、电一体化的高新技术产品。该硬度计造型新颖,具有良好的可靠性,可操作性和直观性。可进行布氏、洛氏、维氏三种试验方法测试,具备了八级试验力的多功能硬度计,能满足多种硬度测试需求。试验力的加荷、保荷、卸荷采用自动切换,操作简便迅速。
    触摸式操作直观显示测试内容。通过触摸点击选择测试方法,一键式启动硬度测试无需提前人工施加初实验力、实验力值实时显示更加直观、确保力值的真实性。力值与时间实时曲线图显示方便您观察被测工件不同力值下的实时变化。洛氏硬度值自动计算精确到小数点后一位,并提供棒材硬度测试标准避免了硬度结果查表的繁琐。在大屏幕屏上实时显示试验方法、试验力,曲线图、硬度值、试验力保持时间等。此设备提供了超大的16G硬盘可直接对硬度测试数据生成报告,报告中可显示力值与时间曲线图。可生成专业的硬度测试报告,通过打印机输出。
    性能特点:
    1,10寸平板电脑,Win8.1操作系统;
    2,闭环传感器控制系统,无需砝码;
    3,无需特殊安装,甚至无需售后;
    4,无需施加初始试验力,自动加卸试验力;
    5,测量精度高,洛氏硬度值自动修正;
    6,测试过程中显示实时曲线;
    7,随时将数据导入电脑;
    8,硬度标尺选择时,提示选用压头;
    9. 布氏、洛氏、维氏硬度的三种试验方法测试;
    10.塑料洛氏标尺的选择(特殊要求,按合同供货)
    11.执行标准GB/T230.1、GB/T230.2、GB/T231.1、GB/T231.2、GB/T4340.1、GB/T3440.2、JJG112
    硬度计的技术参数
    1、硬度标尺:洛氏:HRA,HRB,HRC,HRD,HRE,HRF,HRG,HRH,HRK
    布氏:HBW2.5/31.25,HBW2.5/62.5,,HBW5/62.5HBW2.5/187.5
    维氏:HV30,HV100
    2、试验力:洛氏试验力:588N(60Kg),980N(100Kg),1471N(150Kg)
    布氏试验力:306.5N(31.25Kg),612.9N(62.5Kg),1839N(187.5Kg)
    维氏试验力:29.2N(30Kg),980.7N(100Kg)
    3、硬度测试范围:洛氏:HRA:20~88、HRB:20~100、HRC:20~70
    布氏:HBW:8HBW~650HBW
    维氏:40HV~1000HV
    4、读数方式:电脑显示
    5、显微镜放大倍率:布氏37.5X,维氏75X
    6、压头中心到机身距离:210mm
    7、被测试件允许最大高度:
    7.1测试洛氏硬度:220mm
    7.2测试布氏、维氏硬度:170mm
    8、硬度计外形尺寸(长×宽×高):580×260×780mm
    9、仪器重量约:80kg

    HBRVW-187.5 Hardness Tester supplied by CHWES. 0 key specifications available on request.

    02

    仕様

    * Generated by rule engine over the product database; for pre-selection only.

    03

    測定原理

    Hardness testing presses an indenter into the surface under a constant load and converts indentation size or depth into a hardness value. Vickers uses a 136° diamond pyramid: HV = 0.1891 × F(N)/d²(mm), where d is the mean diagonal.

    Hot hardness is performed in vacuum or high-purity inert gas. Specimen and indenter are heated independently and must be at the same temperature or corrected per the standard; loading, dwell and unloading all happen inside the hot zone, and the indentation is measured through a high-temperature optic or after cooling. The HMAS series uses a uniform hot zone with ±5 °C uniformity from 200 to 1600 °C.

    • Vickers 0.01–100 kgf: full range, thin layers and case-depth gradients.
    • Rockwell C 150 kgf: fast batch checking of hardened parts.
    • Brinell: castings, annealed and coarse-grain materials.
    • Leeb: portable rebound testing on large parts.
    04

    Process animation

    1. Preparation: polish to Ra ≤ 0.4 µm, remove work-hardened layers.
    2. Mount and align: place the specimen, position the indenter over the test point.
    3. Heat up (hot hardness): evacuate to ≤10⁻² Pa or backfill argon, ramp and soak.
    4. Load: apply force at the set rate, dwell 10–15 s.
    5. Measure: read diagonals or depth, compute HV/HRC.
    6. Gradient: step along depth and plot hardness versus distance.
    0102030405
    05

    Calculation & formulas

    1. Rockwell: HR = K − h/0.002 (K = 100 for HRC, 130 for HRB). At h = 0.078 mm, HRC = 61.

    2. Brinell: HBW = 2F/(πD(D−√(D²−d²))); with F=1838.6 N, D=2.5 mm, d=1.1 mm, HBW ≈ 192.

    3. Vickers: HV = 0.1891·F/d² (F in N); F=9.807 N with d=0.05 mm gives HV ≈ 742.

    4. Test forces: choose Brinell loads by 0.045F/D²; Rockwell 10 kgf preliminary with 60/100/150 kgf total; surface scales 3 / 15/30/45 kgf.

    5. Conversions: HRC ≈ HBW/10 only as a rough mid-range guide — official reports must follow the GB/T 1172 tables.

    06

    規格

    StandardTitleScope
    GB/T 4340.1-2009Vickers hardness test — test methodVickers
    GB/T 230.1-2018Rockwell hardness testRockwell
    GB/T 231.1-2018Brinell hardness testBrinell
    ISO 6507-1Vickers hardness testExport
    ASTM E92Vickers hardness of metallic materialsAmericas
    GB/T 17394.1-2014Leeb hardness testPortable

    Hot hardness has no unified national standard; ASTM E92 practice is normally cited with temperature, atmosphere, dwell and indenter material stated in the report.

    07

    選定ガイド

    1. Principle follows the target: Rockwell for macro hardness and heat-treatment acceptance; Brinell for cast iron, annealed and forged parts where a large indent is representative; Vickers or micro-Vickers for thin layers, coatings and small areas.

    2. Bench or portable: bench units (HRC-150SMJ, HBRVS-187.5) where parts can be brought in; portable Leeb for large moulds, in-service piping and non-removable parts, corrected against a bench reference, typically within ±2 HRC.

    3. One for many: mixed, low-volume shops do well with a Brinell-Vickers-Rockwell combination unit covering HRA/HRB/HRC/HV/HB.

    4. Automation: manual below 100 parts per operator per day; motorised elevation, automatic loading and data upload (HRC-150SMJ) above 200 or for unattended runs.

    5. Reference blocks: two to three blocks covering the working range, checked every shift and sent for annual calibration.

    6. Specimen requirements: Rockwell needs thickness at least ten times the indent depth and Ra ≤1.6 µm; otherwise switch to Vickers or superficial Rockwell.

    ModelPrincipleRangeTypical use
    HRC-150SMJRockwell, motorised digitalHRA/HRB/HRCBatch sampling in heat treatment
    HRC-150SM / HRC-150MRockwellHRA/HRB/HRCIncoming and in-process checks
    HRC-45MSuperficial Rockwell15N/30N/45NSheet, plating, case layers
    HRS-150M / XHRS-150MDigital RockwellHRA/HRB/HRCLines needing data upload
    HBRVS-187.5Brinell-Vickers-RockwellHBW/HRA/HRB/HRC/HVMixed low-volume production

    Three rules for trustworthy data: check the reference block every shift and record it; keep the support face flat and clean; keep indent spacing at least three indent diameters.

    08

    試験方法

    Specimen. Test and support faces parallel; thickness at least 1.5 × diagonal (Vickers) or 10 × depth (Rockwell); Ra ≤ 0.4 µm, free of scale and oil.

    Room temperature. Select load, apply within 10–15 s, dwell 10–15 s, unload, measure diagonals. Spacing between indentations ≥3d, from the edge ≥2.5d.

    Hot hardness. Load the specimen, evacuate or backfill argon, ramp and soak 20–30 min, lower the indenter, load and dwell, unload, cool or measure hot, then apply the temperature correction.

    Gradient. Step every 0.05–0.1 mm to the hardness plateau; determine effective case depth at 550 HV1 per GB/T 9450.

    Quality control. Check a certified block (e.g. 700 HV1) each shift, recalibrate beyond ±3%, and log furnace curves and atmosphere for hot tests.

    09

    Industry applications

    • Heat-treatment shops: Rockwell HRC sampling of quenched and tempered parts, carburised surface hardness, Brinell HBW on annealed stock.
    • Castings and forgings: body hardness and HAZ values, section hardness gradients indicating cooling rate and structural uniformity.
    • Moulds and tools: HRC versus wear resistance after hardening and tempering, edge-to-core hardness difference on cutting tools.
    • Thin and small parts: case-hardened layers, coatings and sheet need Vickers or superficial Rockwell (HBRVS-187.5 covers HRA/HRB/HRC/HV/HB).
    • Bearings and gears: ring and raceway hardness, case-to-core difference against carburising requirements.
    • Pressure vessels and piping: weld and HAZ hardness to detect brittle microstructures, typically ≤350 HV10.
    • Incoming verification: hardness as the fastest screening method when material grades are mixed, confirmed by OES.
    • Field and in-service: portable Leeb or ultrasonic hardness testers on large immovable parts, corrected against a bench reference.
    10

    Price and lead time for this model

    By submitting you agree to our privacy policy.

    ⇄0比較仕様比較